Letters of Interpretation

OSHA requirements are set by statute, standards, and regulations. Our interpretation letters explain these requirements and how they apply to particular circumstances, but they cannot create additional employer obligations. Each letter constitutes OSHA's interpretation of the requirements discussed.

Note that our enforcement guidance may be affected by changes to OSHA rules. Also, from time to time we update our guidance in response to new information.

These letters of interpretation and the standards they address may not apply to OSHA State Plans. State Plans are required to have standards and enforcement programs that are at least as effective as OSHA's and may have different or additional requirements. Please see OSHA-approved State Plans for more information.

Filters


Date Title Standard Number
Requirement for a safety latch on a sling hook depends on the activity for which the sling is being used. 1910.181(a)(29), 1910.181(j)(2), 1910.184(c)(6), 1917.45, 1918.66, 1918.81, 1926.753
OSHA's machine guarding requirements provide no exemption from guarding based on shaft size or speed. 1910.219(c)(2)(i), 1910.219(c)(5)
Notification requirements for concrete compressive strength and anchor bolt modifications. 1926.752(a), 1926.752(a)(2), 1926.752(b), 1926.755(b), 1926.755(b)(2)
Use of passing trays and single-handed scalpel blade remover in a surgical setting. 1910.1030, 1910.1030(c)(1)(iv), 1910.1030(d)(2)
Rail extensions for a portable ladder;step-through ladder device. 1926.1053(b)(1), 1910.25(d)(2)
Whether gas-actuated fastening tools require the same individual training for each model as powder-actuated fastening tools. 1926.21(b)(2), 1926.302(e), 1910.243(d)
Determining if an injury is considered a new recordkeeping case based on a recurrence of previously recorded symptoms. 1904 - Table of Contents, 1904.5(b)(3), 1904.6
Clarification of the retail facilities exemption under the PSM standard. 1910.119, 1910.119(a)(2)(i)
"Freehand" piercing without the use of forceps or other engineering controls violates the bloodborne pathogens standards. 1910.1030, 1910.1030(d)(2)(i)
Clarification of "potential atmospheric hazard" when reclassifying a PRCS as a non-permit required confined space. 1910.146(b), 1910.146(c)(7), 1910.146(c)(7)(i)
Clarification on recording days away from work for follow-up visits to doctor while on restricted-duty job and recovery time to stabilize preexisting condition. 1904 - Table of Contents, 1904.5(b)(2)(ii)
Qualifications for interpreting/classifying chest roentenograms and maintenance of interpretation forms. 1910.1001, 1910.1001(m)(3), 1910.1001(m)(5), 1910.1020, 1910.1020(d)(1), 1910.1020(d)(1)(i)
Use of ANSI/ISA S84.00.01-2004 Parts 1-3 (IEC 61511 MOD) to comply with OSHA's Process Safety Management standard 1910.119
Fall protection requirements for workers on guardrail-equipped platforms. 1926.451(g)(1), 1926.451(g)(4)
Enhanced risk of damage/degradation of insulation integrity on temporary wiring with prolonged use 1910.269
Clarification of "continuous forced air ventilation" for PRCS entry work. 1910.146(c)(5)(i), 1910.146(c)(5)(ii)(E)
Once medical treatment beyond first aid has occurred for injury or illness the case must be recorded. 1904 - Table of Contents, 1904.7(b)
A worm drive gearbox is not considered to be a holding brake. 1910.179, 1910.179(a)(2), 1910.179(f)(1)(i), 1910.179(f)(1)(ii)
Acceptability of slip on fittings on stair rails and requirement for stair rails to be smooth surfaced. 1910.23, 1910.23(e)(1)
OSHA regulations applicable to materials used on asphalt tank farms. 1910.106