Point of operation guarding for cutters on milling machines.

Archive Notice - OSHA Archive

NOTICE: This is an OSHA Archive Document, and may no longer represent OSHA Policy. It is presented here as historical content, for research and review purposes only.

OSHA requirements are set by statute, standards and regulations. Our interpretation letters explain these requirements and how they apply to particular circumstances, but they cannot create additional employer obligations. This letter constitutes OSHA's interpretation of the requirements discussed. Note that our enforcement guidance may be affected by changes to OSHA rules. Also, from time to time we update our guidance in response to new information. To keep apprised of such developments, you can consult OSHA's website at https://www.osha.gov.

 

 

February 18, 1976

 

 

MEMORANDUM FOR: ALFRED BARDEN
REGIONAL ADMINISTRATOR
Subject: 29 CFR 1910.212(a)(3)(ii) and (iv)

 

Point of operation guarding for cutters on milling machines.

Archive Notice - OSHA Archive

NOTICE: This is an OSHA Archive Document, and may no longer represent OSHA Policy. It is presented here as historical content, for research and review purposes only.

OSHA requirements are set by statute, standards and regulations. Our interpretation letters explain these requirements and how they apply to particular circumstances, but they cannot create additional employer obligations. This letter constitutes OSHA's interpretation of the requirements discussed. Note that our enforcement guidance may be affected by changes to OSHA rules. Also, from time to time we update our guidance in response to new information. To keep apprised of such developments, you can consult OSHA's website at https://www.osha.gov.

 

 

February 18, 1976

 

 

MEMORANDUM FOR: ALFRED BARDEN
REGIONAL ADMINISTRATOR
Subject: 29 CFR 1910.212(a)(3)(ii) and (iv)

 

Point of operation guarding for cutters on milling machines.

Archive Notice - OSHA Archive

NOTICE: This is an OSHA Archive Document, and may no longer represent OSHA Policy. It is presented here as historical content, for research and review purposes only.

OSHA requirements are set by statute, standards and regulations. Our interpretation letters explain these requirements and how they apply to particular circumstances, but they cannot create additional employer obligations. This letter constitutes OSHA's interpretation of the requirements discussed. Note that our enforcement guidance may be affected by changes to OSHA rules. Also, from time to time we update our guidance in response to new information. To keep apprised of such developments, you can consult OSHA's website at https://www.osha.gov.

 

 

February 18, 1976

 

 

MEMORANDUM FOR: ALFRED BARDEN
REGIONAL ADMINISTRATOR
Subject: 29 CFR 1910.212(a)(3)(ii) and (iv)

 

Point of operation guarding for cutters on milling machines.

Archive Notice - OSHA Archive

NOTICE: This is an OSHA Archive Document, and may no longer represent OSHA Policy. It is presented here as historical content, for research and review purposes only.

OSHA requirements are set by statute, standards and regulations. Our interpretation letters explain these requirements and how they apply to particular circumstances, but they cannot create additional employer obligations. This letter constitutes OSHA's interpretation of the requirements discussed. Note that our enforcement guidance may be affected by changes to OSHA rules. Also, from time to time we update our guidance in response to new information. To keep apprised of such developments, you can consult OSHA's website at https://www.osha.gov.

 

 

February 18, 1976

 

 

MEMORANDUM FOR: ALFRED BARDEN
REGIONAL ADMINISTRATOR
Subject: 29 CFR 1910.212(a)(3)(ii) and (iv)

 

Point of operation guarding for cutters on milling machines.

Archive Notice - OSHA Archive

NOTICE: This is an OSHA Archive Document, and may no longer represent OSHA Policy. It is presented here as historical content, for research and review purposes only.

OSHA requirements are set by statute, standards and regulations. Our interpretation letters explain these requirements and how they apply to particular circumstances, but they cannot create additional employer obligations. This letter constitutes OSHA's interpretation of the requirements discussed. Note that our enforcement guidance may be affected by changes to OSHA rules. Also, from time to time we update our guidance in response to new information. To keep apprised of such developments, you can consult OSHA's website at https://www.osha.gov.

 

 

February 18, 1976

 

 

MEMORANDUM FOR: ALFRED BARDEN
REGIONAL ADMINISTRATOR
Subject: 29 CFR 1910.212(a)(3)(ii) and (iv)

 

Point of operation guarding for cutters on milling machines.

Archive Notice - OSHA Archive

NOTICE: This is an OSHA Archive Document, and may no longer represent OSHA Policy. It is presented here as historical content, for research and review purposes only.

OSHA requirements are set by statute, standards and regulations. Our interpretation letters explain these requirements and how they apply to particular circumstances, but they cannot create additional employer obligations. This letter constitutes OSHA's interpretation of the requirements discussed. Note that our enforcement guidance may be affected by changes to OSHA rules. Also, from time to time we update our guidance in response to new information. To keep apprised of such developments, you can consult OSHA's website at https://www.osha.gov.

 

 

February 18, 1976

 

 

MEMORANDUM FOR: ALFRED BARDEN
REGIONAL ADMINISTRATOR
Subject: 29 CFR 1910.212(a)(3)(ii) and (iv)

 

Point of operation guarding for cutters on milling machines.

Archive Notice - OSHA Archive

NOTICE: This is an OSHA Archive Document, and may no longer represent OSHA Policy. It is presented here as historical content, for research and review purposes only.

OSHA requirements are set by statute, standards and regulations. Our interpretation letters explain these requirements and how they apply to particular circumstances, but they cannot create additional employer obligations. This letter constitutes OSHA's interpretation of the requirements discussed. Note that our enforcement guidance may be affected by changes to OSHA rules. Also, from time to time we update our guidance in response to new information. To keep apprised of such developments, you can consult OSHA's website at https://www.osha.gov.

 

 

February 18, 1976

 

 

MEMORANDUM FOR: ALFRED BARDEN
REGIONAL ADMINISTRATOR
Subject: 29 CFR 1910.212(a)(3)(ii) and (iv)

 

Point of operation guarding for cutters on milling machines.

Archive Notice - OSHA Archive

NOTICE: This is an OSHA Archive Document, and may no longer represent OSHA Policy. It is presented here as historical content, for research and review purposes only.

OSHA requirements are set by statute, standards and regulations. Our interpretation letters explain these requirements and how they apply to particular circumstances, but they cannot create additional employer obligations. This letter constitutes OSHA's interpretation of the requirements discussed. Note that our enforcement guidance may be affected by changes to OSHA rules. Also, from time to time we update our guidance in response to new information. To keep apprised of such developments, you can consult OSHA's website at https://www.osha.gov.

 

 

February 18, 1976

 

 

MEMORANDUM FOR: ALFRED BARDEN
REGIONAL ADMINISTRATOR
Subject: 29 CFR 1910.212(a)(3)(ii) and (iv)

 

Lockout/tagout requirements for servicing manually-controlled vertical/horizontal milling machine and drill press tool changes.

OSHA requirements are set by statute, standards and regulations. Our interpretation letters explain these requirements and how they apply to particular circumstances, but they cannot create additional employer obligations. This letter constitutes OSHA's interpretation of the requirements discussed. Note that our enforcement guidance may be affected by changes to OSHA rules. Also, from time to time we update our guidance in response to new information. To keep apprised of such developments, you can consult OSHA's website at https://www.osha.gov.

August 24, 2005

Mr. William H. Kincaid
Lockton Companies of St. Louis
Three City Place Drive
Suite 900
St. Louis, MO 63141

Dear Mr. Kincaid: