Powered by GoogleTranslate

Inspection Detail

Case Status: CLOSED
Inspection: 1227935.015 - Alco Manufacturing Corporation, Llc

Inspection Information - Office: Toledo

Nr: 1227935.015Report ID: 0524700Open Date: 04/27/2017

Alco Manufacturing Corporation, Llc
10584 Middle Ave.
Elyria, OH 44035
Union Status: NonUnion
SIC:
NAICS: 332721/Precision Turned Product Manufacturing
Mailing: 10584 Middle Ave., Elyria, OH 44035

Inspection Type:Referral
Scope:Partial Advanced Notice:N
Ownership:Private
Safety/Health:Safety Close Conference:04/27/2017
Emphasis: N:AmputateClose Case:10/02/2018

Related Activity:TypeIDSafetyHealth
 Referral1203531 Yes  
Case Status: CLOSED

Violation Summary
Serious Willful Repeat Other Unclass Total
Initial Violations 1 2 1 4
Current Violations 1 1 2
Initial Penalty $9,959 $0 $69,713 $0 $0 $79,672
Current Penalty $9,000 $0 $0 $3,000 $0 $12,000
FTA Amount $0 $0 $0 $0 $0 $0

Violation Items
# ID Type Standard Issuance Abate Curr$ Init$ Fta$ Contest LastEvent
  1. 01001A Other 19101030 C01 I 06/23/2017 09/30/2018 $3,000 $9,959 $0 07/13/2017 J - ALJ Decision
  2. 01001B Other 19101030 F01 I 06/23/2017 09/30/2018 $0 $0 $0 07/13/2017 J - ALJ Decision
  3. 01001C Other 19101030 G02 I 06/23/2017 09/30/2018 $0 $0 $0 07/13/2017 J - ALJ Decision
  4. 01002 Serious 19100147 C07 I C 06/23/2017 09/30/2018 $9,000 $69,713 $0 07/13/2017 J - ALJ Decision
Deleted 5. 02001B Repeat 19100147 F01 06/23/2017 06/30/2017 $0 $0 $0 07/13/2017 J - ALJ Decision
Deleted 6. 03001 Other 19100147 C06 II 06/23/2017 07/19/2017 $0 $0 $0 07/13/2017 J - ALJ Decision

Accident Investigation Summary
Summary Nr: 95051.015Event: 04/19/2017Employee'S Hand Is Degloved During Maintenance
At 12:00 p.m. on April 19, 2017, an employee was assisting a coworker to troubleshoot a malfunction of an Amada CNC machine (model number: S-10, serial number: 131) that resulted in a coolant leak. After the coworker removed two panels, normally affixed on the front and side of the machined, and determined that metal chips were blocking the coolant drainage, the employee approached the machine and began helping his coworker remove the metal chips. Much of the metal chips accumulated behind the guard of the machine. As the employee used a magnet and was pulling chips from the side panel access, the CNC turret indexed forward and struck his right hand, pinning it against the inside of the machine's frame. His hand was caught in a sheer point, resulting in its degloving. The incident investigation revealed that the machine was not locked out during the maintenance task and steps to protect against injury during the troubleshooting portion of the inspection were not implemented.
Keywords: caught in, caught between, caught by, hand, lockout/tagout
Inspection Degree Nature Occupation
1 1227935.015 Hospitalized injury Cut/Laceration Machine operators, not specified

Thank You for Visiting Our Website

You are exiting the Department of Labor's Web server.

The Department of Labor does not endorse, takes no responsibility for, and exercises no control over the linked organization or its views, or contents, nor does it vouch for the accuracy or accessibility of the information contained on the destination server. The Department of Labor also cannot authorize the use of copyrighted materials contained in linked Web sites. Users must request such authorization from the sponsor of the linked Web site. Thank you for visiting our site. Please click the button below to continue.

Close