Powered by GoogleTranslate

Inspection Detail

Inspection: 313163115 - Capitol Steel Fabricators Inc

Inspection Information - Office: Santa Ana District Office

 

Inspection Nr: 313163115
Report ID: 0950631
Date Opened: 12/01/2009

Site Address:
Capitol Steel Fabricators Inc
14491 Beach Blvd
Westminster, CA 92683

Mailing Address:
3565 So Greenwood Ave, Commerce, CA 90040

Union Status: NonUnion

SIC:1791

NAICS: 238120/Structural Steel and Precast Concrete Contractors


Inspection Type: Accident

Scope: Partial

Advanced Notice: N

Ownership: Private

Safety/Health: Safety

Close Conference: 03/02/2010

Planning Guide: Safety-Construction

Emphasis:

Case Closed: 02/17/2011


Related Activity
Type Activity Nr Safety Health
Accident 102588647
Violation Summary
Violations/Penalties Serious Willful Repeat Other Unclass Total
Initial Violations 2 2
Current Violations 2 2
Initial Penalty $15,635 $0 $0 $0 $0 $15,635
Current Penalty $12,900 $0 $0 $0 $0 $12,900
FTA Penalty $0 $0 $0 $0 $0 $0

Violation Items
# Citation ID Citaton Type Standard Cited Issuance Date Abatement Due Date Current Penalty Initial Penalty FTA Penalty Contest Latest Event Note
1. 01001 Serious 3646 B 03/03/2010 03/08/2010 $12,600 $12,600 $0 03/15/2010 W - Empr Withdrew  
2. 02001 Serious 3646 D 03/03/2010 03/08/2010 $300 $3,035 $0 03/15/2010 F - Formal Settlement  

Investigation Summary

Investigation Nr: 202551248
Event: 12/01/2009
Employee Suffers Multiple Fractures in Scissor Lift Fall

On December 1, 2009, Employee #1 was moving a beam lying on the concrete foundation of the building to be constructed. The Division measured the beam at approximately 37 feet long by 17. 75 inches wide. The approximate weight of the beam was 1,200 lbs. Employee #1 and a coworker both rigged the scissor lifts that were about 20 feet apart with a two-foot by four-foot piece of wood, or two by four, through the railing. One side of the cable was wrapped around the two by four, with the other around the beam. The beam was lifted approximately four feet over some pipes sticking upwards out of the concrete. Employee #1 lifted the beam, overloading the two scissor lifts. One scissor lift, manufactured by Skyjack, Model Number SJ111-3219, Serial Number 22017082, was raised approximately 10-13 feet and tipped over during the lift of the beam. The capacity of the Skyjack retracted was 550 pounds and 250 pounds extended. The second scissor lift did not tip over. It was manufactured by Genie, Model GS2632, serial number GS3206 82544. Its capacity was 500 pounds retracted and 250 pounds extended. Employee #1 suffered serious fractures when the scissor lift tipped over. Employee #1 was a permanent full time employee of this employer with no other contracts. The fire department called the Division to report a serious injury that occurred.

Keywords: BEAM, FRACTURE, TANDEM LIFT, FALL, CONCRETE

Investigated Inspection
# Inspection Age Sex Degree of Injury Nature of Injury Occupation
1 313163115 Hospitalized injury Fracture Miscellaneous material moving equipment operators
Back to Top

Thank You for Visiting Our Website

You are exiting the Department of Labor's Web server.

The Department of Labor does not endorse, takes no responsibility for, and exercises no control over the linked organization or its views, or contents, nor does it vouch for the accuracy or accessibility of the information contained on the destination server. The Department of Labor also cannot authorize the use of copyrighted materials contained in linked Web sites. Users must request such authorization from the sponsor of the linked Web site. Thank you for visiting our site. Please click the button below to continue.

Close