Translate
Inspection Detail
Inspection: 312917560 - Ogle'S Custom Cabinets
Inspection Information - Office: Fresno District Office
Site Address:
Ogle'S Custom Cabinets
23362 Ave 14
Madera, CA 93637
Mailing Address:
, , 00000
Union Status: NonUnion
SIC:2434
NAICS: 337110/Wood Kitchen Cabinet and Countertop Manufacturing
Inspection Type: Accident
Scope: Partial
Advanced Notice: N
Ownership: Private
Safety/Health: Safety
Close Conference: 11/23/2010
Emphasis:
Case Closed: 04/07/2015
| Type | Activity Nr | Safety | Health |
|---|---|---|---|
| Accident | 101081974 |
| Violations/Penalties | Serious | Willful | Repeat | Other | Unclass | Total |
|---|---|---|---|---|---|---|
| Initial Violations | 3 | 2 | 5 | |||
| Current Violations | 1 | 3 | 4 | |||
| Initial Penalty | $17,885 | $0 | $0 | $5,195 | $0 | $23,080 |
| Current Penalty | $1,200 | $0 | $0 | $1,200 | $0 | $2,400 |
| FTA Penalty | $0 | $0 | $0 | $0 | $0 | $0 |
| # | Citation ID | Citaton Type | Standard Cited | Issuance Date | Abatement Due Date | Current Penalty | Initial Penalty | FTA Penalty | Contest | Latest Event | Note |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 1. | 01001 | Other | 342 A | 12/01/2010 | 12/06/2010 | $1,000 | $5,000 | $0 | 12/23/2010 | F - Formal Settlement | |
| 2. | 01002 | Other | 3203 A | 12/01/2010 | 01/03/2011 | $100 | $195 | $0 | 12/23/2010 | F - Formal Settlement | |
| 3. | 02001 | Serious | 3203 A07 C | 12/01/2010 | 01/03/2011 | $0 | $3,150 | $0 | 12/23/2010 | F - Formal Settlement | Citation has been deleted. |
| 4. | 03001 | Other | 3328 G | 12/01/2010 | 01/03/2011 | $100 | $3,935 | $0 | 12/23/2010 | F - Formal Settlement | |
| 5. | 04001 | Serious | 43180001 A | 12/01/2010 | 01/03/2011 | $1,200 | $10,800 | $0 | 12/23/2010 | F - Formal Settlement |
Investigation Summary
"On April 2, 2010, Employee #1, a cabinet worker, was using a Rockwell Spindle Shaper, Model Number 34-340, to check the profile of a raised panel door cutting tool against an existing door profile. Initially, Employee #1 ran a board of oak 12 inches long by 6 inches wide by .75 inches high through the shaper. Employee #1 made a second run with a 12-inch-long by 2.5 inches wide by .75 inches high board (NOTE: the actual piece material was not available and conflicting information indicates the material may have been a nominal 2.25 inches). As the end of the board ran passed the cutting tool, the material tipped into the tool causing Employee #1 hand to contact the rotating tool. The contact resulted in partial amputation of digits 2, 4 and fracture of the third digit of the right hand. On July 1, 2010, an employee of Ogles Custom Cabinet contacted the Division, seeking information pertaining to the injury he received during his employment on April 2, 2010. It was verified the Division was not notified and the employees injuries were serious as defined by 8CCR Section 330(h). An inspection of the shaper revealed an effective guard for the cutting tool was not provided as required by 8CCR 4318.1(a) and a table insert was not present. The absence of the insert is considered a significant factor in conjunction when milling narrow width material. Working on narrow material is identified as a known shaper hazard, although the importance of the table insert in emphasized in the manufacturers operators manual or the literature. Both employers Injury and Illness Prevention Program (IIPP) and employee training were determined to be ineffective."
Keywords: ROTATING PARTS, AMPUTATED, FINGER, GUARD, LACERATION, SPINDLE, WOOD SHAPER, HAND
| # | Inspection | Age | Sex | Degree of Injury | Nature of Injury | Occupation |
|---|---|---|---|---|---|---|
| 1 | 312917560 | Hospitalized injury | Amputation | Cabinet makers and bench carpenters |