Violation Detail
Standard Cited: 19100212 A01 General requirements for all machines.
Inspection Nr: 1350744.015
Citation: 01014
Citation Type: Serious
Abatement Date: 3
Initial Penalty: $13,260.00
Current Penalty: $11,249.00
Issuance Date: 03/26/2019
Nr Instances: 26
Nr Exposed: 19
Related Event Code (REC):
Gravity: 10
Report ID: 0215800
Contest Date: 04/11/2019
Final Order: 09/16/2019
Emphasis:
Type | Latest Event | Event Date | Penalty | Abatement Due Date | Citation Type | Failure to Abate Inspection |
---|---|---|---|---|---|---|
Penalty | F: Formal Settlement | 09/16/2019 | $11,249.00 | Serious | ||
Penalty | C: Contested | 04/15/2019 | $13,260.00 | Serious | ||
Penalty | Z: Issued | 03/26/2019 | $13,260.00 | Serious |
Text For Citation: 01 Item/Group: 014 Hazard:
29 CFR 1910.212(a)(1): Machine guarding was not provided to protect operator(s) and other employees from hazard(s) created by pinch points, ingoing nip points, rotating parts, and moving parts: a) Bldg. 76-1, on or about 10/5/18: Pinch point between the push bar and guard on the Wagner saw #34593 conveyor end was not adequately guarded in that there was an opening at the left side where push bar retracts. b) Bldg. 76-1, on or about 10/5/18: Pinch points created by the moving table on the Mattison surface grinder #42453 and on the Gallmeyer Livingston surface grinder #34865 were not guarded. c) Bldg. 65-1, on or about 10/10/18: Ingoing nip points on the Remstar tool carousel #39627 were not adequately guarded in that the light curtain guarding device was not functioning properly to shut down the moving carousel. d) Bldg. 58-1, Almco Line, on or about 10/12/18: Pinch points between the cleated return conveyor and guarding for the Almco aluminum line #33668 and steel line #42443 were not guarded. e) Bldg. 50-1, on or about 10/12/18: Rotating spindle end and nut projection on a Divine polishing jack #N1992R and #N1873 were not guarded on the right sides. f) Bldg. 48-1, on or about 10/12/18: Rotating shafts, spindle end and nut projections on Divine barrel polishing jacks #32261 at both wheels were not guarded and rotating shaft, spindle end and nut projection on the right wheel on Divine barrel polishing jack #32734 were not guarded. g) Bldg. 48-1, on or about 10/12/18: Pinch points on the discharge end of a chip conveyor for the Okuma CNC #42113 were not guarded. h) Bldg. 46-1, on or about 10/16/18: Pinch point between bracket on frame of Cincinnati OD grinder #28926 and moving table was not guarded. i) Bldg. 46-1, on or about 10/16/18: Rotating nut projection on the motor drive for the Chevalier OD grinder #42011 was not guarded and the moving table was not guarded at the ends at a passageway. j) Bldg. 46-1, on or about 10/16/18: Rotating shafts on the fixtures for the Almco tumbler #38239 were not guarded. k) Bldg. 48-2, Electrical Shop, on or about 10/16/18: Unused portion of blade on a MSC horizontal bandsaw was not guarded on the left side. l) Bldg. 48-2, Electrical Shop, on or about 10/16/18: Rotating spindles and chucks on a Delta drill press #N2108 and an Allen drill press #N2106 were not guarded. m) Bldg. 52-3A, on or about 10/23/18: Rotating spindle ends and nut projections on two pedestal buffers #N0056 and #N1625 were not guarded on either side. n) Bldg. 48-3, on or about 10/23/18: Moving elevator on the new Transfer machine #34301, at the rear of the machine, was not guarded. o) Bldg. 46-3, on or about 10/24/18: Pinch parts, nip points and moving parts were not guarded on two Rem Special trigger mills #28618 and #30245. p) Bldg. 82-1, on or about 10/24/18: Moving table for the Shaker furnace #31278 was not adequately guarded in that the latch for the doors guarding the moving table was broken preventing the doors from staying closed. q) Bldg. 84-3, on or about 10/25/18: Rotating nut projection and unused portion of sanding belt below the work rest on a Kalamazoo belt sander #N0026 were not guarded. r) Bldg. 84-4, across from entrance, next to column, on or about 10/25/18: Unused portion of blade on a MSC horizontal bandsaw #N2404, was not guarded. s) Bldg. 46-4, New Gen Cell, on or about 10/25/18: Rotating nut projection and unused portion of sanding belt below the work rest on a belt sander next to 700 repair cell, were not guarded.