Scheduled Maintenance - President's Day Weekend
The U.S. Department of Labor will be conducting scheduled system maintenance beginning Friday, Feb. 15 at 5 p.m. ET through Tuesday, Feb. 19 at 8 a.m. ET. Some pages may be temporarily unavailable. To report an emergency, file a complaint with OSHA, or to ask a safety and health question, call 1-800-321-6742 (OSHA).

eTools Home :Lead: Secondary Lead Smelter Scope | Definitions | References | Credits
Lead: Secondary Lead Smelter



Smelting  > Blast Furnace                     

Blast furnaces are designed and operated to produce a hard (high alloy content) lead product. Blast furnaces emit high levels of lead fume during the the following processes: Cross-sectional view of  blast furnace
Additional blast furnace images
Blast furnace lead tap controls
Click for larger view of blast furnace lead tap controls diagram


Charging

Cross-sectional diagram of blast furnace
Click for larger view of blast furnace diagram

Potential Sources of Exposure:
  • Spillage or emissions may occur at blast furnace feed conveyor transfer points and charging points.

  • Spillage of lead-containing dust may occur if bucket elevators, conveyors, or skip hoists are overfilled.

  • Lead fume and dust may be emitted from the blast furnace if the charge level is too low.
Possible Engineering and Work Practice Controls:
  • Maintain raw material storage and handling areas under negative pressure to prevent contamination of adjacent work areas.

  • Prevent puffing by providing and maintaining process controls to ensure that the proper amount of charge material is in the thimble on the top of the furnace.

  • Provide hooding with sufficient exhaust ventilation at furnace feed conveyor loading and charge points to capture dusts and fumes which may be emitted.

  • Provide hooding with sufficient exhaust ventilation to capture dusts which may be generated when charging the furnace.

  • Do not overfill bucket elevators, conveyors, or skip hoists.

  • Maintain positive-pressure, HEPA filtered air systems on mobile equipment to ensure effective operation. Check and change air filters regularly as part of an effective scheduled preventative maintenance program.

  • Vacuum any spills immediately with a HEPA filtered vacuum system. Water should not be used in the smelting area for dust suppression due to the possibility of oxide fires and the mixing of water and molten lead.
 


Tapping
Blast furnace slag tapping
Fig. 1. Slag tap with enclosure hooding and local exhaust ventilation
Blast furnace tapping operations involve removing the slag and then tapping molten lead from the furnace into molds or ladles. Some smelters tap metal directly into a holding kettle which keeps the metal molten for refining. The other smelters cast the furnace metal into blocks and allow the blocks to solidify.  

Potential Sources of Exposure:
  • Lead fumes may be emitted at the lead or slag tapping plugs during removal of the tapping plug or while lancing the tapping plug.

  • Emissions may occur while pouring lead or slag at the tapping launder, mold, ladle, or refining kettle.

  • Lead dust may become airborne due to disturbance of settled dust in the smelting area.

  • Emissions may occur from ladles containing slag or molten lead.

  • Spilled slag or molten lead may emit lead fumes.

Possible Engineering and Work Practice Controls:
Secondary exhaust hood diagram
Click for larger view of secondary exhaust hood diagram
 


Tuyere Punching
Fig. 2. Manual Tuyere Punch
Fig. 2. Manual tuyere punching
Blast air for the combustion process enters the blast furnace through "tuyeres." The tuyeres occasionally begin to fill with accretions and must be physically punched, usually with a steel rod, to keep them unobstructed. The conventional method used for this task is to remove the cover of the tuyeres and insert the steel rod. After the accretions have been "punched," the cover is replaced.

Recently smelters have been able to adapt an "off-the-shelf" automatic tuyere puncher that has greatly reduced employee lead exposure. However, even with the automatic system there are occasions when the tuyere pipe has to be cleared by using a jackhammer or rod.

Potential Sources of Exposure:
  • Significant lead fume emissions may come from the furnace during manual punching.
Possible Engineering and Work Practice Controls:
Fig. 3. Automatice tuyere punch system
Fig. 3. Automatic tuyere puncher
  • Provide automatic tuyere punching.
    Hydraulic Tuyere Punch Diagram

  • Use notched, rotating tuyere covers to minimize tuyere opening during punching.

  • Stand to the side of the tuyere when opening the cover during the tuyere punching operation.

  • Provide a rod of sufficient length to minimize operator exposure.

  • Provide a viewing port on the tuyere cover so that plugging can be observed without removing the cover.
 


Additional Images
Fig. 4. Lifting recently cast lead blocks from mold
Fig. 4. Lifting recently cast lead blocks from mold


Fig. 5. Slag side of blast furnace
Fig. 5. Slag side of blast furnace


Fig. 6. Lead side of blast furnace
Fig. 6. Local exhaust ventilation at lead tap

Fig. 7. Automatic tuyere punch
Fig. 7. Automatic tuyere punch


Fig. 8. Liquid lead cooling in molds
Fig. 8. Liquid lead cooling in molds


Fig. 9. Lead flowing into mold
Fig. 9. Lead flowing into mold


 



eTools Home :Lead: Secondary Lead Smelter Scope | Definitions | References | Credits