US Dept of Labor

Occupational Safety & Health AdministrationWe Can Help

Regulations (Standards - 29 CFR) - Table of Contents
• Part Number: 1917
• Part Title: Marine Terminals
• Subpart: G
• Subpart Title: Related Terminal Operations and Equipment
• Standard Number: 1917.151
• Title: Machine guarding.
• GPO Source: e-CFR

1917.151(a)

Definition. "Guarded" means shielded, fenced, or enclosed by covers, casings, shields, troughs, spillways or railings, or guarded by position or location. Examples of guarding methods are guarding by location (positioning hazards so they are inaccessible to employees) and point of operation guarding (using barrier guards, two-handtripping devices, electronic safety devices, or other such devices).

1917.151(b)

General.

1917.151(b)(1)

Danger zones on machines and equipment used by employees shall be guarded.

1917.151(b)(2)

Where chips and dust produced by machine operation may result in a hazard to the operator, the machinery shall be equipped with an effective exhaust system at the point of origin, or other equally effective means shall be provided to protect the operator.

1917.151(b)(3)

Fixed machinery shall be secured to prevent shifting.

1917.151(b)(4)

A power cut-off device for machinery and equipment shall be provided at the operator's working position.

..1917.151(b)(5)

1917.151(b)(5)

Machines driven by belts and shafting shall be fitted with a beltlocking or equivalent protective device if the belt can be shifted.

1917.151(b)(6)

In operations where injury to the operator might result if motors were to restart after power failures, provisions shall be made to prevent machines from automatically restarting upon restoration of power.

1917.151(b)(7)

The power supply to machines shall be turned off, locked out, and tagged out during repair, adjustment, or servicing.

1917.151(b)(8)

Machines shall be maintained in a safe working condition.

1917.151(b)(9)

Only designated employees shall maintain or repair machinery and equipment.

1917.151(b)(10)

Machines with defects that affect the safety of operation shall not be used.

1917.151(c)

Hand-fed circular ripsaws and hand-fed circular crosscut table saws. Unless fixed or manually adjustable enclosures or guarding provides equivalent protection, hand-fed circular ripsaws and hand-fed circular crosscut table saws shall be guarded as follows to keep employees clear of any danger zones:

1917.151(c)(1)

They shall be equipped with hoods completely enclosing those portions of the saw above the table and the material being cut;

..1917.151(c)(2)

1917.151(c)(2)

They shall have spreaders to prevent material from squeezing the saw. Spreaders shall be in true alignment with the saw. Spreaders may be removed only during grooving, dadoing, or rabbeting operations, and shall be replaced at the completion of such operations; and

1917.151(c)(3)

They shall have non-kickback fingers or dogs to oppose the tendency of the saw to pick up material or throw material toward the operator.

1917.151(d)

Swing cutoff saws.

1917.151(d)(1)

Swing cut-off saws shall have hoods completely enclosing the upper half of the saw, the arbor end and the point of operation at all saw positions to protect the operator from material thrown up by the saw. The hood shall automatically cover the lower portion of the blade, so that when the saw returns to the back of the table the hood rises on top of the fence, and when the saw is moved forward the hood drops on top, remaining in contact with the table or the material.

1917.151(d)(2)

Swing cutoff saws shall have a device to return the saw automatically to the back of the table without rebound. The device shall not be dependent upon rope, cord or springs.

1917.151(d)(3)

Devices shall be provided to prevent saws from swinging beyond the front or back edges of the table.

..1917.151(d)(4)

1917.151(d)(4)

Inverted swing cutoff saws shall have hoods covering the part of the saw protruding above the table top or material being cut. Hoods shall automatically adjust to the thickness of, and remain in contact with, material being cut.

1917.151(e)

Radial saws. Unless fixed or manually adjustable enclosures or guards provide equivalent protection, radial saws shall be guarded as follows:

1917.151(e)(1)

The upper hood of radial saws shall enclose the upper portion of the blade up to and including the end of the saw arbor and shall protect the operator from being struck by debris. The sides of the lower exposed portion of the blade shall be guarded to the blade diameter by a device automatically adjusting to the thickness of the stock and remaining in contact with the stock. The lower guard may be removed only when the saw is used for bevel cuts;

1917.151(e)(2)

Radial saws used for ripping shall have non-kickback fingers or dogs on both sides to oppose the thrust or tendency of the saw to pick up material or throw material toward the operator;

1917.151(e)(3)

Adjustable stop shall be provided to prevent travel of radial saw blades beyond the table's edge;

1917.151(e)(4)

Radial saws shall be installed so that the cutting head returns to the starting position without rebound when released; and

..1917.151(e)(5)

1917.151(e)(5)

The employer shall direct that employees perform ripping and ploughing against the saw turning direction. Rotation direction and an indication of the end of the saw to be used shall be conspicuously marked on the hood.

1917.151(f)

Band saws and band resaws.

1917.151(f)(1)

Saw blades and band saw wheels shall be enclosed or guarded, except for the working portion of the blade between the bottom of the guide rolls and the table, to protect employees from point-of-operation hazards and flying debris.

1917.151(f)(2)

Band saws shall be equipped with brakes to stop the band saw wheel if the blade breaks.

1917.151(f)(3)

Band saws shall be equipped with a tension control device to keep the blade taut.

1917.151(g)

Abrasive wheel and machinery.

1917.151(g)(1)

Abrasive wheels shall be used only on machines having enclosure guards to restrain pieces of grinding wheels and to protect employees if the wheel breaks, except as provided in paragraphs (g)(2) and (g)(3) of this section. Where the operator must stand in front of the safety guard opening, the safety guard shall be adjustable or have an adjustable tongue or piece at the top of the opening. The safety guard or the tongue shall be adjusted so that they are always close to the periphery of the wheel. Guards shall be aligned with the wheel and the strength of fastenings shall be greater than the strength of the guard.

..1917.151(g)(2)

1917.151(g)(2)

When the work provides equivalent protection, or when the machine is designed as a portable saw, guards may be constructed with the spindle end, nut and outer flange exposed. When the work entirely covers the side of the wheel, the side covers of the guard may be removed.

1917.151(g)(3)

Guarding is not required:

1917.151(g)(3)(i)

For wheels used for internal work while the wheel is contained within the work being ground; or

1917.151(g)(3)(ii)

For mounted wheels 2 inches (5 cm) and smaller in diameter used in portable operation.

1917.151(g)(4)

Work rests shall be used on fixed grinding machines. Work rests shall be rigidly constructed and adjustable for wheel wear. They shall be adjusted closely to the wheel with a maximum opening of 1/8-inch (3.18 mm) and shall be securely clamped. Adjustment shall not be made while the wheel is in motion.

1917.151(g)(5)

Grinding wheels shall fit freely on the spindle. The spindle nut shall be tightened only enough to hold the wheel in place.

1917.151(g)(6)

Grinding machine wheels shall turn at a speed that is compatible with the rated speed of the wheel.

1917.151(g)(7)

Flanges and blotters shall be used only with wheels designed for their use. Flanges shall be of a type ensuring retention of pieces of the wheel in case of breakage.

..1917.151(g)(8)

1917.151(g)(8)

Abrasive wheels with operational defects shall not be used.

1917.151(h)

Rotating parts, drives and connections.

1917.151(h)(1)

Rotating parts, such as gears and pulleys, that are located 7 feet (2.13 m) or less above working surfaces shall be guarded to prevent employee contact with moving parts.

1917.151(h)(2)

Belt, rope and chain drives shall be guarded to prevent employees from coming into contact with moving parts.

1917.151(h)(3)

Gears, sprockets and chains shall be guarded to prevent employees from coming into contact with moving parts. This requirement does not apply to manually operated sprockets.

[65 FR 40942, June 30, 2000]


Next Standard (1917.152)

Regulations (Standards - 29 CFR) - Table of Contents

Thank You for Visiting Our Website

You are exiting the Department of Labor's Web server.

The Department of Labor does not endorse, takes no responsibility for, and exercises no control over the linked organization or its views, or contents, nor does it vouch for the accuracy or accessibility of the information contained on the destination server. The Department of Labor also cannot authorize the use of copyrighted materials contained in linked Web sites. Users must request such authorization from the sponsor of the linked Web site. Thank you for visiting our site. Please click the button below to continue.

Close