Powered by GoogleTranslate
OSHA News Release - Table of Contents

DOL Logo OSHA News Release – Region 6

U.S. Department of Labor

Region 6 News Release: 14-1397-DAL
Aug. 7, 2014
Contact: Diana Petterson      Juan Rodriguez
Phone: 972-850-4710      972-850-4709
Email: petterson.diana@dol.gov      rodriguez.juan@dol.gov

OSHA cites Texas plastics manufacturer for 21 violations, including 6 repeat,
for exposing workers to injuries from unexpected machine startups
Plastic Systems LLC fined $174,240

EL PASO, Texas – Plastic Systems LLC was cited by the U.S. Department of Labor's Occupational Safety and Health Administration for 21 safety and health violations, including six repeat, for failing to develop adequate lockout/tagout procedures to control the unexpected startup of the company's plastic injection molding machines. Proposed penalties total $174,240. The inspection was conducted in February 2014 after a safety referral was made during a health inspection initiated under the Combustible Dust National Emphasis Program.

"Inspectors found workers at risk of potential injuries from preventable workplace hazards, including the unexpected startup of machinery during maintenance or servicing, the lack of machine guarding and electrical hazards," said Joann Figueroa, OSHA's area director in El Paso. "OSHA's standards must be followed to keep workers safe."

The six repeat violations, with a penalty of $112,860, were cited for failing to address specific lockout/tagout techniques for the servicing and maintenance of machinery and conduct annual inspections of these techniques and procedures. The employer failed to ensure workers had operable portable fire extinguishers and were trained to use them. Improper maintenance resulted in electrical hazards, including conductors with damaged insulation. A repeat violation is issued when an employer previously has been cited for the same or a similar violation of a standard, regulation, rule or order at any other facility in federal enforcement states within the last five years. Plastic Systems was cited previously in a 2011 inspection at the El Paso facility.

The remaining 15 violations, including 11 serious with a penalty of $61,380, were cited for failure to ensure workers knew the type and magnitude of energy that needed lockout control; provide machine guarding on injection molding machines; maintain electrical components and equipment in a manner that complies with safety requirements; properly record injuries and illnesses; adequately distribute portable fire extinguishers; and replace damaged circuit breaker boxes. A serious violation occurs when there is substantial probability that death or serious physical harm could result from a hazard about which the employer knew or should have known.

The citations can be viewed at: http://www.osha.gov/ooc/citations/PlasticSystemsLLC958341_0807_14.pdf*

Plastic Systems, headquartered in Romeo, Michigan, designs and manufactures plastic molded products and assemblies using plastic injection molding. The company, which employs about 80 workers at its El Paso location, has 15 business days from receipt of its citations to comply, request an informal conference with OSHA's El Paso area director, or contest the citations and penalties before the independent Occupational Safety and Health Review Commission.

To ask questions, obtain compliance assistance, file a complaint, or report workplace hospitalizations, fatalities or situations posing imminent danger to workers, the public should call OSHA's toll-free hotline at 800-321-OSHA (6742) or the agency's El Paso office at 915-534-6251.

Under the Occupational Safety and Health Act of 1970, employers are responsible for providing safe and healthful workplaces for their employees. OSHA's role is to ensure these conditions for America's working men and women by setting and enforcing standards, and providing training, education and assistance. For more information, visit http://www.osha.gov.


U.S. Department of Labor news materials are accessible at http://www.dol.gov. The department's Reasonable Accommodation Resource Center converts departmental information and documents into alternative formats, which include Braille and large print. For alternative format requests, please contact the department at (202) 693-7828 (voice) or (800) 877-8339 (federal relay).

* Accessibility Assistance: Contact OSHA's Office of Communications at 202-693-1999 for assistance accessing PDF materials.

OSHA News Release - Table of Contents

Thank You for Visiting Our Website

You are exiting the Department of Labor's Web server.

The Department of Labor does not endorse, takes no responsibility for, and exercises no control over the linked organization or its views, or contents, nor does it vouch for the accuracy or accessibility of the information contained on the destination server. The Department of Labor also cannot authorize the use of copyrighted materials contained in linked Web sites. Users must request such authorization from the sponsor of the linked Web site. Thank you for visiting our site. Please click the button below to continue.