Powered by GoogleTranslate

Alert: Due to routine maintenance on the OSHA website, some pages are temporarily unavailable.
To file a complaint with OSHA or to ask a safety and health question, call 1-800-321-6742 (OSHA).

Standard Interpretations - (Archived) Table of Contents
• Status: Archived

Archive Notice - OSHA Archive

NOTICE: This is an OSHA Archive Document, and may no longer represent OSHA Policy. It is presented here as historical content, for research and review purposes only.

July 13, 1993

Mr. James D. Miller
Safety Director
J.E. Dunn Construction Company
929 Holmes
Kansas City, MO 64106-2682

Dear Mr. Miller:

This is in response to your May 13 letter in which you request the Occupational Safety and Health Administration (OSHA) to comment on the design and use of positioning hook on concrete I apologize for the delay in responding to your inquiry.

OSHA currently has no construction standards that apply to positioning devices. As you know, to address this type of equipment, OSHA issued a Notice of Proposed Rulemaking for Subpart M -- Fall Protection on November 25, 1986 (51 FR 42718). In the notice (copy of relevant pages are enclosed) it was proposed to require positioning device connecting assemblies to have a minimum tensile strength of 5000 pounds. That rule was intended to ensure that if a positioning device component is used in a body belt/harness system, it would have the proper capacity to handle the larger impact forces. That rule has not been finalized and comments to the record indicate that lower capacity hardware (down to at least twice the potential impact load) should be allowed if the hardware is clearly marked or attached to the positioning device system in such a way that it cannot be used in a body belt/harness system where greater forces are likely to occur. If your equipment meets this concern, then it would meet the intent of the proposed rule.

If you need further assistance, please don't hesitate to contact me or Mr. Dale Cavanaugh of my staff at (202) 219-8136.


Roy F. Gurnham, P.E., Esq. Director
Office of Construction and Maritime
Compliance Assistance

May 13, 1993

Mr. Roy Gurnaham
Director of Construction
Compliance USDOL/OSHA
200 Constitution Ave, NW
Washington, DC 20210

Dear Mr. Gurnaham:

I am writing to you for your help in determining if a positioning hook used on concrete formwork meets current OSHA standards.

The construction industry has a unique problem with modular forming systems. The slots in these form panels preclude the use of a standard hook because the openings are too small to allow the hook to pass through. Consequently, as a matter of need, some workers attempt to "manufacture" job-made hooks to use as a positioning device. This practice is strictly prohibited but has continued to be a serious problem.

To counteract this problem, a hook has been developed that would be used specifically as a positioning device on modular form panels. The hook has been tested to approximately 4000 pounds without failure. Under normal circumstances, the worker would be limited to a fall of 18-24 inches while using the hook with a chain assembly.

As a contractor, we strive to provide the safest working environment for our workers. We feel that we have found a safer device than what is currently available on the market.

If this hook was to be manufactured, would it meet or exceed OSHA strength requirements for positioning devices? Your consideration in this mater would be greatly appreciated.

If you have any questions regarding this hook, feel free to call me at (816) 391-2546.



James D. Miller
Safety Director

Archive Notice - OSHA Archive

NOTICE: This is an OSHA Archive Document, and may no longer represent OSHA Policy. It is presented here as historical content, for research and review purposes only.

Standard Interpretations - (Archived) Table of Contents

Thank You for Visiting Our Website

You are exiting the Department of Labor's Web server.

The Department of Labor does not endorse, takes no responsibility for, and exercises no control over the linked organization or its views, or contents, nor does it vouch for the accuracy or accessibility of the information contained on the destination server. The Department of Labor also cannot authorize the use of copyrighted materials contained in linked Web sites. Users must request such authorization from the sponsor of the linked Web site. Thank you for visiting our site. Please click the button below to continue.