Powered by GoogleTranslate

Occupational Safety and Health Administration OSHA

Inspection Detail

Inspection: 310297122 - Progressive Marketing Products Inc/Premier Mounts

Inspection Information - Office: Ca Santa Ana District Office

Nr: 310297122Report ID: 0950631Open Date: 03/26/2009

Progressive Marketing Products Inc/Premier Mounts
3150 Miraloma Ave
Anaheim, CA 92806
Union Status: NonUnion
SIC: 3499/Fabricated Metal Products, Not Elsewhere Classified
NAICS: 332510/Hardware Manufacturing
Mailing: 3130 Miraloma Ave, Anaheim, CA 92806

Inspection Type:Accident
Scope:Partial Advanced Notice:N
Ownership:Private
Safety/Health:Safety Close Conference:06/01/2009
Planning Guide: Safety-Manufacturing Close Case:09/15/2009

Related Activity:TypeIDSafetyHealth
 Accident102585676    

Violation Summary
Serious Willful Repeat Other Unclass Total
Initial Violations 1 1 2
Current Violations 1 1 2
Initial Penalty $16,200 $0 $0 $650 $0 $16,850
Current Penalty $16,200 $0 $0 $650 $0 $16,850
FTA Amount $0 $0 $0 $0 $0 $0

Violation Items
# ID Type Standard Issuance Abate Curr$ Init$ Fta$ Contest LastEvent
  1. 01001 Other 4203 B 06/03/2009 06/26/2009 $650 $650 $0 -
  2. 02001 Serious 4214 A 06/03/2009 06/26/2009 $16,200 $16,200 $0 -

Accident Investigation Summary
Summary Nr: 202550158Event: 03/20/2009Employee Amputates Two Fingertips In Punch Press
On March 20, 2009, Employee #1, a temporary contract employee, was operating an Amada press brake (Model FBD III 1253 NT, Serial Number 1253307B) and worked for an employer that manufactured various types of mounting and holding structures for television sets, monitors and other display equipment. Employee #1 was working on an 11 guage cold rolled steel piece measuring 78.75 inches long and 4.85 inches wide. He had already bent this part at the middle of its width, but the angle was slightly larger than the exact 90 degree bend desired. His supervisor, Employee #2, asked him to increase the amount of pressure via the control panel and bend this part again to get a more precise right angle. This press brake was equipped with a die having two parallel V grooves at the bottom part of the point of operation. These two V grooves were about 1.5 inches apart. The top punch ram could be aligned to mate with either of these two V grooves. Employee #1 placed the previously bent piece mistakenly in the inner groove while the punch ram was set to mate with the outer groove. He was holding the part with his hands when he activated the press via the foot pedal. When the die closed, his two index fingertips were crushed between the work piece and the lower die. Employee #1 lost about 0.75 inches of the fingertips on both his index fingers, which included loss of both nails and substantial amounts of bone on both fingers. He was treated in the emergency room and was not hospitalized.
Keywords: die, amputated, finger, machine operator, crushed, point of operation, punch press
Inspection Degree Nature Occupation
1 310297122 Non Hospitalized injury Amputation Misc. metal,plastic,stone&glass-working mach. op's

Thank You for Visiting Our Website

You are exiting the Department of Labor's Web server.

The Department of Labor does not endorse, takes no responsibility for, and exercises no control over the linked organization or its views, or contents, nor does it vouch for the accuracy or accessibility of the information contained on the destination server. The Department of Labor also cannot authorize the use of copyrighted materials contained in linked Web sites. Users must request such authorization from the sponsor of the linked Web site. Thank you for visiting our site. Please click the button below to continue.

Close