Powered by GoogleTranslate

Occupational Safety and Health Administration OSHA

Inspection Detail

Inspection: 126174523 - Joe Nasr Construction

Inspection Information - Office: Ca Los Angeles

Nr: 126174523Report ID: 0950641Open Date: 04/11/2001

Joe Nasr Construction
4384 Mentone Ave.
Culver City, CA 90230
Union Status: NonUnion
SIC: 1521/General Contractors-Single-Family Houses
Mailing: 2912 Overland Ave., Rancho Park, CA 90064

Inspection Type:Accident
Scope:Partial Advanced Notice:N
Ownership:Private
Safety/Health:Safety Close Conference:06/12/2001
Emphasis: S:Construction (Cship)Close Case:11/12/2004

Related Activity:TypeIDSafetyHealth
 Accident362568263    

Violation Summary
Serious Willful Repeat Other Unclass Total
Initial Violations 1 4 5
Current Violations 1 3 4
Initial Penalty $10,800 $0 $0 $870 $0 $11,670
Current Penalty $0 $0 $375 $685 $0 $1,060
FTA Amount $0 $0 $0 $0 $0 $0

Violation Items
# ID Type Standard Issuance Abate Curr$ Init$ Fta$ Contest LastEvent
  1. 01001 Other 1509 A 06/15/2001 07/15/2001 $250 $250 $0 07/30/2001 F - Formal Settlement
  2. 01002 Other 1509 B 06/15/2001 07/15/2001 $250 $250 $0 07/30/2001 F - Formal Settlement
  3. 01003 Other 1512 C01 06/15/2001 07/15/2001 $185 $185 $0 07/30/2001 F - Formal Settlement
Deleted 4. 01004 Other 23950059 06/15/2001 07/15/2001 $0 $185 $0 07/30/2001 F - Formal Settlement
  5. 02001 Repeat 4307 A 06/15/2001 07/02/2001 $375 $10,800 $0 07/30/2001 F - Formal Settlement

Accident Investigation Summary
Summary Nr: 201162419Event: 03/20/2001Employee Injured By Circular Saw
At approximately 9:40 a.m. on March 20, 2001, Employee #1 was engaged in framing a roof for a one story residential building. The work was done from standing on top of an 8 foot scaffold located on the ground. Employee #1 and another employee were working together, taking measurements and cutting a 10-foot-long 2 by 8, to size, using a Skill Model Number HD77 Worm Drive circular saw. The ends of the rafters were cut out at a 45 degree angle using the skill saw and were then nailed to the hip. Employee #1 and the other employee had completed putting up 10 such pieces on the south section, and were getting ready to cut another. As Employee #1 was raising the plugged-in tool with his finger on the switch, he activated the trigger switch which caused the skill saw to start unexpectedly. Employee #1 lacerated his right leg along the side of the knee with the rotating sharp blade. The blade guard was not used. Employee #1 was transported to Brotman Medical Center where he was hospitalized for his injury.
Keywords: knee, roof, building, finger, guard, circular saw, rafter, laceration, leg, scaffold
Inspection Degree Nature Occupation
1 126174523 Hospitalized injury Cut/Laceration Carpenters

Thank You for Visiting Our Website

You are exiting the Department of Labor's Web server.

The Department of Labor does not endorse, takes no responsibility for, and exercises no control over the linked organization or its views, or contents, nor does it vouch for the accuracy or accessibility of the information contained on the destination server. The Department of Labor also cannot authorize the use of copyrighted materials contained in linked Web sites. Users must request such authorization from the sponsor of the linked Web site. Thank you for visiting our site. Please click the button below to continue.

Close