Powered by GoogleTranslate

UNITED STATES
DEPARTMENT OF LABOR

Occupational Safety and Health Administration OSHA

Contact Us FAQ A to Z Index English Español

Return to Accident Search Results

Accident Report Detail

Accident: 201340395 - Burn - Electrical Fault In Regulator

Accident: 201340395 -- Report ID: 0729700 -- Event Date: 06/03/1998
InspectionOpen DateSICEstablishment Name
30101368606/05/19984911Western Resources
A three-person power line crew was replacing one of a set of three voltage regulators at a substation. The crew consisted of a substation supervisor and two substation electricians. The crew's maintenance supervisor stopped by to observe the operation. The crew obtained switching orders to deenergize the three regulators, which were located on the east side of the substation. The bad regulator was located on the south end of the regulator bank. The crew bypassed the load on the regulators and deenergized them. The crew then replaced the malfunctioning regulator with an Allis-Chalmers regulator (Serial No. 3-3740-00228-9). After the crew visually determined that the controls were in the neutral position as required by the manufacturer, the two electricians took a break. One of them was at the back of the maintenance truck, which was located about 4.3 meters south-southwest of the new regulator. The other electrician was further forward. While these two employees were on break, the substation supervisor closed the bus-side contacts on the three regulators, energizing them. He then closed the load-side contacts. About 5 minutes passed since the supervisor energized the south regulator, but none of the regulators was under full load, as the bypasses were shunting load around the regulators. When the supervisor opened the bypass switch for the new regulator and placed it under load, the regulator failed. The internal pressure in the regulator forced open its lid directly in line with the first electrician, who was sitting on the back of the truck. A large quantity of burning oil from the regulator struck him. The oil also struck the other electrician and the maintenance supervisor, but they were apparently not injured. The second electrician and the substation supervisor extinguished the flames on the injured employee, while the maintenance supervisor summoned emergency medical services with his radio. The injured employee was transported to a local hospital and transferred to a burn center, where he died of complications resulting from second- and third-degree burns over 80 percent of his body.
Keywords: burn, electric arc, electrical, flammable liquid, power line worker, e ptd, elec utility work, electrical fault, elec equipment--misc
Employee # Inspection Age Sex Degree Nature Occupation
1 301013686 Fatality Burn/Scald(Heat) Electricians

Accident: 170888259 - Burn - Electrical Fault In Electric Cable

Accident: 170888259 -- Report ID: 0950615 -- Event Date: 08/19/1997
InspectionOpen DateSICEstablishment Name
12550913308/21/19974911Pacific Gas And Electric Company
A power line worker was performing a switching operation. The employee was standing over an open underground vault located under a sidewalk. He was using a 2.4-meter-long live-line tool to close a switch on a 12-kilovolt backup circuit feeding three transformers. The switch was normally open; it was closed only to reroute power when the primary circuit was out. The normal anticipated load to be applied to the backup circuit was 15 amperes, and the 1-0 AWG cables for the backup circuit were rated at 25 kilovolts and 200 amperes. When the employee closed the switch, the cable failed. The ensuing electric arc burned the employee. He was hospitalized with first-degree burns to his face and arms and second-degree burns to the underside of his upper arms.
Keywords: burn, electric arc, electrical, electric switch, power line worker, electric cable, e ptd, elec utility work, electrical fault
Employee # Inspection Age Sex Degree Nature Occupation
1 125509133 Hospitalized injury Burn/Scald(Heat) Electrical power installers and repairers

Accident: 170632699 - Burn - Electrical Fault In Transformer

Accident: 170632699 -- Report ID: 0950644 -- Event Date: 03/31/1997
InspectionOpen DateSICEstablishment Name
12612496503/31/19974911Southern Calif. Edison
Two power line workers were working on a utility pole, replacing one transformer in a bank of three. The employees replaced the defective Central Transformer Co. transformer (Serial No. 2370474314) with a new Howard Industries transformer (Serial No. 1260760597). The other two transformers in the bank were manufactured by Central Transformer Co. (Serial No. 2370474813) and McGraw-Edison (Serial No. 69VK084005). After the transformer was replaced, one of the power line workers tested the transformers for voltage and asked the customer to close the main power switch. After about 50 seconds, the McGraw-Edison transformer failed. The oil inside the transformer ignited and sprayed over the pole, the employees, and their truck, which was parked nearby. Both employees died of electric shock and burns received in the accident. (The cause of the electric shock was not noted on the original form.)
Keywords: burn, electric arc, overhead power line, electrical, power line worker, e ptd, elec utility work, electric shock, electrical fault, transformer
Employee # Inspection Age Sex Degree Nature Occupation
1 126124965 Fatality Electric Shock Electrical power installers and repairers
2 126124965 Fatality Electric Shock Electrical power installers and repairers

Accident: 170762769 - Burn - Electrical Fault In Regulator

Accident: 170762769 -- Report ID: 0950622 -- Event Date: 03/27/1996
InspectionOpen DateSICEstablishment Name
11980080303/28/19964931Pg & E
Two journeyman high-voltage electricians were dispatched to a substation to troubleshoot a regulator that was not responding to automatic control. They had completed a low-voltage relay examination and replaced a loose Porter Brumfield relay in its socket. They then placed the controls on manual, adjusted voltage, and returned the regulator to automatic control to determine whether it was functioning correctly. The stepping device moved one step, and then the regulator failed, spewing burning insulating oil out of the overpressure vent. The hot oil burned both employees. One of them died of his injuries.
Keywords: burn, electric arc, electrical, electrician, e ptd, substation, elec utility work, electrical fault, elec equipment--misc
Employee # Inspection Age Sex Degree Nature Occupation
1 119800803 Fatality Burn/Scald(Heat) Electricians
2 119800803 Non Hospitalized injury Burn/Scald(Heat) Electricians

Accident: 170358428 - Burn - Electrical Fault In Disconnect Switch

Accident: 170358428 -- Report ID: 0950631 -- Event Date: 12/12/1995
InspectionOpen DateSICEstablishment Name
12012385602/27/19964911So Cal Edison
Two power line workers were asked by their supervisor to perform a switching operation at a substation. They were given a written switching order for this task. Following the written procedure in the order, they opened a disconnect that was energized at 12 kilovolts. Apparently, the disconnect failed, causing an electrical fault. The two employees sustained second- and third-degree burns as a result of the ensuing electric arc. They were hospitalized for their injuries.
Keywords: burn, clothing, electric arc, electrical, electric switch, power line worker, e ptd, elec utility work, electrical fault
Employee # Inspection Age Sex Degree Nature Occupation
1 120123856 Hospitalized injury Burn/Scald(Heat) Electrical and electronic technicians
2 120123856 Hospitalized injury Burn/Scald(Heat) Electrical and electronic technicians

Accident: 170891899 - Burn - Electrical Fault In Switch

Accident: 170891899 -- Report ID: 0950635 -- Event Date: 04/06/1995
InspectionOpen DateSICEstablishment Name
11213015805/16/19954911Southern California Edison
A repair crew for an electric utility was working the night shift, repairing and switching a faulted 11-kilovolt circuit. A switch, which was located inside an underground vault that had water in it, was to be replaced. A sump pump was used to remove the water, but the crew's supervisor ordered one of the employees into the vault while the water was still 2 feet deep. As the switch was being removed, numerous parts were lost. Additionally, the replacement equipment was not of the same design as the original equipment. Apparently, as the employee was reassembling the switch, it fell into an energized position and failed. The resultant electric arc burned the employee, who was hospitalized for his injuries. (The supervisor stated that the injured employee had been adequately trained and warned of the hazardous conditions.)
Keywords: burn, electric arc, electrical, electric switch, power line worker, equipment failure, e ptd, elec utility work, electrical fault, water
Employee # Inspection Age Sex Degree Nature Occupation
1 112130158 Hospitalized injury Burn/Scald(Heat) Electrical power installers and repairers

Accident: 170727697 - Burn - Electrical Fault In Switch

Accident: 170727697 -- Report ID: 0950615 -- Event Date: 01/18/1994
InspectionOpen DateSICEstablishment Name
11973471301/18/19944911P G & E, Geyser Power Plant
Three power line workers were opening a 13.8-kilovolt switch so that work could be performed on a power line to a transformer. After checking back to the 115-kilovolt circuit breakers on the high-voltage side of the transformer, one of the employees unlocked the operating bar for the switch and placed its handle in the open position. His two coworkers were standing behind him in single file. The employee operating the handle moved it first to its normal open position and then moved it a little more. This caused the switch to fail, creating an electrical fault. The ensuing electric arc ignited the oil in the switch, and the burning oil spewed out. The employee who opened the switch was burned on his face, neck, and hands by the hot oil and flash fire. His neck and face were lacerated by flying metal switch parts. He was hospitalized for treatment of his second-degree burns. The other two employees sustained minor burns on their faces, necks, hands, and arms. They were treated for their burns at the emergency room of a local hospital and released.
Keywords: burn, electric arc, electrical, electric switch, power line worker, e ptd, elec utility work, electrical fault
Employee # Inspection Age Sex Degree Nature Occupation
1 119734713 Hospitalized injury Burn/Scald(Heat) Electrical and electronic technicians
2 119734713 Non Hospitalized injury Burn/Scald(Heat) Electrical and electronic technicians
3 119734713 Non Hospitalized injury Burn/Scald(Heat) Electrical and electronic technicians

Accident: 170749873 - Burn - Electrical Fault In Live-Line Tool

Accident: 170749873 -- Report ID: 0352430 -- Event Date: 08/18/1993
InspectionOpen DateSICEstablishment Name
11951702708/18/19934911Baltimore Gas And Electric Company
A power line crew for an electric utility was phasing an electric generator to a power line. A nylon screw in the test stick failed, causing an electrical fault. The ensuing electric arc burned five of the employees; one of them was severely burned. Four of the five employees were hospitalized for their injuries. The crew was well trained and qualified to perform this job. The crew members were wearing proper personal protective equipment, which, in most cases, prevented more severe injury.
Keywords: burn, clothing, electric arc, electrical, power line worker, live-line tool, e ptd, elec utility work, electric conductor, electrical fault
Employee # Inspection Age Sex Degree Nature Occupation
1 119517027 Hospitalized injury Burn/Scald(Heat) Electrical power installers and repairers
2 119517027 Non Hospitalized injury Burn/Scald(Heat) Electrical power installers and repairers
3 119517027 Hospitalized injury Burn/Scald(Heat) Electrical power installers and repairers
4 119517027 Hospitalized injury Burn/Scald(Heat) Electrical power installers and repairers
5 119517027 Hospitalized injury Burn/Scald(Heat) Electrical power installers and repairers

Accident: 14241863 - Burn - Electrical Fault In Meter

Accident: 14241863 -- Report ID: 0627700 -- Event Date: 04/22/1993
InspectionOpen DateSICEstablishment Name
10905843804/22/19934911Public Service Of Oklahoma
Three power line workers for an electric utility were performing preliminary work on a 34-kilovolt distribution circuit that was to be replaced by a 13.2-kilovolt circuit. The employees were testing the transformer secondaries with a rotation meter to determine the phase sequence of the transformers' loads. One of the crew members (employee #2) had just connected the meter, which was rated at 600 volts, to the 2300-volt output. His two coworkers were observing the operation. The underrated meter failed, initiating a phase-to-phase electrical fault. The ensuing electric arc burned the three employees and ignited their clothing (which resulted in further burn injuries). Employees #1 and #2 sustained second- and third-degree burns. The third employee sustained second-degree burns. The employee using the meter thought that the voltage was 480 volts. His coworkers did not inform him of the actual voltage and did not recognize the hazards involved with using the underrated meter.
Keywords: burn, clothing, electric arc, electrical, power line worker, test equipment, e ptd, elec utility work, electrical fault, untrained
Employee # Inspection Age Sex Degree Nature Occupation
1 109058438 Hospitalized injury Burn/Scald(Heat) Electrical power installers and repairers
2 109058438 Hospitalized injury Burn/Scald(Heat) Electrical power installers and repairers
3 109058438 Hospitalized injury Burn/Scald(Heat) Electrical power installers and repairers

Accident: 170238109 - Burn - Electrical Fault In Elbow

Accident: 170238109 -- Report ID: 1055360 -- Event Date: 10/14/1992
InspectionOpen DateSICEstablishment Name
11131520610/20/19924911Tanner Electric Cooperative
A power line worker was working in a 1.2-meter by 2.4-meter electrical vault. The employee used a live-line tool to place a non-load-break elbow on an energized 7200-volt bushing. When the elbow contacted the bushing, it failed and caused a fire in the vault. The employee's clothing ignited. A second employee pulled the injured worker out of the vault and doused the burning clothing. Both employees suffered burns. The second employee was treated at a hospital and released. The first employee was hospitalized for his injuries. (The power line worker knew not to energize a load through a non-load-break elbow, but he mistakenly thought that it was safe to energize an unloaded power line through this type of connection.)
Keywords: burn, clothing, electric arc, electrical vault, electrical, power line worker, e ptd, elec utility work, electrical fault, untrained
Employee # Inspection Age Sex Degree Nature Occupation
1 111315206 Non Hospitalized injury Other Occupation not reported
2 111315206 Hospitalized injury Other Electrical power installers and repairers

Accident: 14343594 - Burn - Electrical Fault In Transfomer

Accident: 14343594 -- Report ID: 0418400 -- Event Date: 03/26/1992
InspectionOpen DateSICEstablishment Name
10900700506/15/19924911Colquitt Electric Membership Corp.
An Allis-Chalmers transformer (Serial No. 21-114-502-424) had been installed in a new substation. While it was being tested, it failed, and the resulting explosion released burning oil onto a foreman for an electric utility crew. The foreman, who had been standing about 2.4 meters away from the transformer while the test was being conducted, was burned on his back. He died of his injuries. The transformer manufacturer inspected the transformer and found that the cause of the explosion was internal failure.
Keywords: burn, clothing, electrical, back, e ptd, substation, elec utility work, electrical fault, transformer
Employee # Inspection Age Sex Degree Nature Occupation
1 109007005 Fatality Burn(Chemical) Supervisors; electricians & power transm. install.

Accident: 170193353 - Burn - Failure Of Underrated Test Equipment

Accident: 170193353 -- Report ID: 0950633 -- Event Date: 08/07/1991
InspectionOpen DateSICEstablishment Name
11206715208/09/19918221Loma Linda University
A power plant operator was working in a high voltage switchgear room. The employee had been assigned the task of installing earthquake clips inside the metal-clad, 4160-volt switchgear. The employee opened the rear of the bus section, exposing the bus and current transformers. The employee believed the current transformers to be step-down transformers. He obtained a tester rated at 600 volts and applied it to the current transformer terminals. The tester failed, and the ensuing electric arc burned the employee, who became engulfed in flames. The employee was severely burned on his arms, torso, and face and was hospitalized for his injuries.
Keywords: burn, clothing, electric arc, electrical, lockout, test equipment, e ptd, elec utility work, electrical fault, switchgear
Employee # Inspection Age Sex Degree Nature Occupation
1 112067152 Hospitalized injury Burn/Scald(Heat) Power plant operators

Thank You for Visiting Our Website

You are exiting the Department of Labor's Web server.

The Department of Labor does not endorse, takes no responsibility for, and exercises no control over the linked organization or its views, or contents, nor does it vouch for the accuracy or accessibility of the information contained on the destination server. The Department of Labor also cannot authorize the use of copyrighted materials contained in linked Web sites. Users must request such authorization from the sponsor of the linked Web site. Thank you for visiting our site. Please click the button below to continue.

Close