eTools Home : Shipyard Employment Scope | Glossary | Additional Resources | Credits
Shipyard Employment eTool
General Requirements Shipbuilding Ship Repair Shipbreaking Barge Cleaning

Materials Handling (including Gear and Equipment for Rigging) Use of Gear


Material-handling equipment (such as cranes and derricks) and rigging gear (slings, shackles, and hooks) must be used correctly and safely to prevent accidents and serious injuries.

Use of Gear
Figure 1: Metal plate lifted using shackles for rigging connections
Figure 1: Metal plate lifted using shackles for rigging connections

Figure 2: Skip being rigged with 4-legged bridle
Figure 2: Skip being rigged with 4-legged bridle

Figure 3: Signal person assisting crane operator when view of load is obstructed
Figure 3: Signal person assisting crane operator when view of load is obstructed

Figure 4: Riggers attaching slings to load with shackles and clamps
Figure 4: Riggers attaching slings to load with shackles and clamps

Figure 5: Improper practice - Worker riding crane hook exposed to fall and entaglement hazards
Figure 5: Improper practice - Worker must not ride crane hook or load

Figure 6: Workers must keep clear of suspended load
Figure 6: Workers must keep clear of suspended load

Figure 7: Ship block properly attached to crane by slings, spreaders and other approved devices
Figure 7: Ship block properly attached to crane by slings, spreaders and other approved devices

Figure 8: Dual lift requires one designated person to coordinate the lift
Figure 8: Dual lift requires one designated person to coordinate the lift
Potential Hazard:

Worker injuries can be caused by falling loads due to rope, chain, or sling failure during the lifting of items due to overloading, worn or defective equipment or improper use of connection of the lifting components.


Requirements and Example Solutions:

Attaching and moving loads
  • Loads must be safely rigged before being hoisted.  [29 CFR 1915.116(b)]
  • Metal plate must be handled on and off hulls by means of: [29 CFR 1915.116(c)]
    • Shackles whenever possible 
    • Welded clips or pads of ample size 
    • Alligator tongs 
    • Grab clamps or screw clamps 
  • Tag lines must be provided on loads likely to swing or to need guidance.  [29 CFR 1915.116(d)]
  • When eye-bolts are used, spreaders may be required to reduce the side pull on the eye-bolt.  [29 CFR 1915.116(e)]
  • Skips must be rigged with a minimum of three-legged bridle. When open-end skips are used, means must be taken to prevent the contents from falling.  [29 CFR 1915.116(g)]
  • Loads (tools, equipment or other materials) must not be swung or be suspended over the heads of workers. [29 CFR 1915.116(j) and 29 CFR 1915.74(a)(12)]
  • When the hoist operator can not see the load, a person to signal the operator is required.  [29 CFR 1915.116(l) and 29 CFR 1915.117(b)]
  • Pallets must be able to support the loads.  [29 CFR 1915.116(m)]
  • Sufficient advance warning must be given before loads or lifting gear are moved.  [29 CFR 1915.116(p)]
  • When ship's gear is used to hoist, a competent person (not the Shipyard Competent Person), must determine that the gear is properly rigged. [29 CFR 1915.117(a)]
  • Shock loading is prohibited. [29 CFR 1910.184(c)(11)]
Working with slings Worker protection
  • Workers must not ride the hook or the load. [29 CFR 1915.116(i)]
  • Hatches, through which materials are moved, must be completely open and hatch covers must be  secured. [29 CFR 1915.116(n)]
  • Hatch covers must not be opened or closed while workers are below the hatch. [29 CFR 1915.116(o)]
  • Workers must not be in between a swinging load and a fixed object. [29 CFR 1915.116(q)]
  • Workers must keep clear of suspended loads and of loads about to be lifted. [29 CFR 1910.184(c)(9)]
  • Hands or fingers must not be placed between the sling and its load while the sling is being tightened around the load. [29 CFR 1910.184(c)(10)]
Using crawler, locomotive, and truck cranes
  • The hoist rope shall not be wrapped around the load. [29 CFR 1910.180(h)(2)(i)]
  • The load shall be attached to the hook by means of slings or other approved devices. [29 CFR 1910.180(h)(2)(ii)]
  • Side loading of booms shall be limited to freely suspended loads. [29 CFR 1910.180(h)(3)(iv)]
  • Cranes must not be used for dragging loads sideways. [29 CFR 1910.180(h)(3)(iv)]
  • Neither the load nor the boom shall be lowered below the point where less than two full wraps of rope remain on their respective drums. [29 CFR 1910.180(h)(3)(x)]
  • When two or more cranes are used to lift one load, one designated person shall be responsible for the operation. He shall be required to analyze the operation and instruct all personnel involved in the proper positioning, rigging of the load, and the movements to be made. [29 CFR 1910.180(h)(3)(xii)]
  • Operators must not be permitted to leave their positions at the controls while the load is suspended. [29 CFR 1910.180(h)(4)(i)]
Back to Top Back to Top


eTools Home : Shipyard Employment Scope | Glossary | Additional Resources | Credits