Newsletter
RSS Feeds
Print This Page
Text Size
Standard Number > 1926 > 1926.302
- 1926.302 - Fasteners used in tools shall be only those specifically manufactured for use in such tools. [03/02/1982]
- 1926.302 - Guarding requirements for a rotary pneumatic angle-drive hand-held tool. [12/11/2001]
- 1926.302 - If work may accidently come into contact with an energized line, do not use a conductive hose. [02/06/1978]
- 1926.302 - Laboratory testing requirements for hand-held electrical construction tools. [12/12/1986]
- 1926.302 - Pneumatic tools must be designed and used in accordance with good engineering practices. [04/08/1982]
- 1926.302 - Pneumatically operated staplers. [05/14/1979]
- 1926.302 - Repair requirements for the cord plug (attachment plug) of double-insulated tools. [05/19/2003]
- 1926.302 - Requirements for leaving construction equipment and powder-actuated tools unattended on a construction building site; impalement protection from reinforcing steel for masonry workers on a scaffold. [05/11/2005]
- 1926.302 - Statement of compliance from OSHA for a pole-mounted powder actuated tool. [09/05/1995]
- 1926.302 - The requirement for fire resistant fluids does not apply to hydraulic tools. [04/03/1978]
- 1926.302 - Whether electric hand tools disassembled and deemed irreparable by a tool repair service are required to be returned disassembled. [03/16/2009]
- 1926.302(a) - All electric tools need to be tested by a qualified national testing laboratory and be listed and labeled. [01/28/1994]
- 1926.302(a) - Marking recognition, regulations and policy of double insulated power tools. [11/08/1985]
- 1926.302(a) - Repair requirements for the cord plug (attachment plug) of double-insulated tools. [05/19/2003]
- 1926.302(a)(1) - Repair requirements for the cord plug (attachment plug) of double-insulated tools. [05/19/2003]
- 1926.302(a)(1) - Whether electric hand tools disassembled and deemed irreparable by a tool repair service are required to be returned disassembled. [03/16/2009]
- 1926.302(b) - Application of OSHA construction standards to govern the use of pneumatic hand tools used in construction for cleaning concrete forms, bridge decks, and roads. [01/19/2005]
- 1926.302(b)(1) - Application of OSHA construction standards to govern the use of pneumatic hand tools used in construction for cleaning concrete forms, bridge decks, and roads. [01/19/2005]
- 1926.302(b)(1) - Use of quick disconnect with "pull-down sleeve" to satisfy requirement of a positive means to prevent pneumatic tools from becoming accidentally disconnected. [11/14/2003]
- 1926.302(b)(3) - Applicability of 1910.212(a)(3)(ii) to Portable Pneumatic Powered Fastener Tools. [03/25/1985]
- 1926.302(b)(4) - Application of OSHA construction standards to govern the use of pneumatic hand tools used in construction for cleaning concrete forms, bridge decks, and roads. [01/19/2005]
- 1926.302(b)(4) - Use of compressed air above 30 p.s.i. for cleaning purposes;nonmetallic-sheathed cable for temporary wiring. [10/04/2000]
- 1926.302(b)(5) - Application of OSHA construction standards to govern the use of pneumatic hand tools used in construction for cleaning concrete forms, bridge decks, and roads. [01/19/2005]
- 1926.302(b)(7) - Application of OSHA construction standards to govern the use of pneumatic hand tools used in construction for cleaning concrete forms, bridge decks, and roads. [01/19/2005]
- 1926.302(b)(7) - Clarification that a safety device to automatically cut off the flow of compressed air applies only to pneumatic power tools. [06/06/1983]
- 1926.302(c) - Standards applicable to Bell Industries "Carb-Cutter" powered tool. [06/05/1985]
- 1926.302(e) - Requirements for leaving construction equipment and powder-actuated tools unattended on a construction building site; impalement protection from reinforcing steel for masonry workers on a scaffold. [05/11/2005]
- 1926.302(e) - Training requirements for powder-actuated tools under §1926.302(e). [03/10/2006]
- 1926.302(e) - Whether gas-actuated fastening tools require the same individual training for each model as powder-actuated fastening tools. [12/21/2005]
- 1926.302(e)(1) - Training requirements for powder-actuated tools under §1926.302(e). [03/10/2006]
- 1926.302(e)(5) - When magazine-fed tools are inspected, the tool is not considered loaded until the magazine feeds the tool. [09/02/1975]
- 1926.302(e)(6) - Requirements for leaving construction equipment and powder-actuated tools unattended on a construction building site; impalement protection from reinforcing steel for masonry workers on a scaffold. [05/11/2005]
- 1926.302(e)(6) - When magazine-fed tools are inspected, the tool is not considered loaded until the magazine feeds the tool. [09/02/1975]
- 1926.302(e)(7) - Interpretation on the use of power activated fasteners being driven into ductile cast iron ingot molds. [07/25/1979]