Disclaimer: These guidelines were developed under contract using generally accepted secondary sources. The protocol used by the contractor for surveying these data sources was developed by the National Institute for Occupational Safety and Health (NIOSH), the Occupational Safety and Health Administration (OSHA), and the Department of Energy (DOE). The information contained in these guidelines is intended for reference purposes only. None of the agencies have conducted a comprehensive check of the information and data contained in these sources. It provides a summary of information about chemicals that workers may be exposed to in their workplaces. The secondary sources used for supplements 111 and 1V were published before 1992 and 1993, respectively, and for the remainder of the guidelines the secondary sources used were published before September 1996. This information may be superseded by new developments in the field of industrial hygiene. Therefore readers are advised to determine whether new information is available.

OCCUPATIONAL SAFETY AND HEALTH GUIDELINE FOR ETHYL BUTYL KETONE

INTRODUCTION

This guideline summarizes pertinent information about ethyl butyl ketone for workers and employers as well as for physicians, industrial hygienists, and other occupational safety and health professionals who may need such information to conduct effective occupational safety and health programs. Recommendations may be superseded by new developments in these fields; readers are therefore advised to regard these recommendations as general guidelines and to determine whether new information is available.

SUBSTANCE IDENTIFICATION

* Formula

C(7)H(14)O

* Structure

(For Structure, see paper copy)

* Synonyms

Butyl ethyl ketone, 3-heptanone, heptan-3-one, n-butyl ethyl ketone, ethyl n-butyl ketone, EBK

* Identifiers

1. CAS No.: 106-35-4

2. RTECS No.: MJ5250000

3. DOT UN: 1224 26 (ketones, liquid, not otherwise stated, n.o.s.)

4. DOT label: Flammable liquid (n.o.s.)

* Appearance and odor

Ethyl butyl ketone is a clear, colorless liquid with a strong, fruity odor.

CHEMICAL AND PHYSICAL PROPERTIES

* Physical data

1. Molecular weight: 114.21

2. Boiling point (at 760 mm Hg): 147 degrees C (296.6 degrees F)

3. Specific gravity: 0.818 at 20 degrees C (68 degrees F)

4. Vapor density: 4.0

5. Melting point: -39 degrees C (-38.2 degrees F)

6. Vapor pressure at 25 degrees C (77 degrees F): 1.4 mm Hg

7. Solubility: Insoluble in water; soluble in alcohol, ether and other organic solvents.

8. Evaporation rate: Data not available.

* Reactivity

1. Conditions contributing to instability: Exposure to sources of ignition such as, heat or open flame should be avoided to prevent a possible fire from occurring.

2. Incompatibilities: Contact between ethyl butyl ketone and acetaldehyde, perchloric acid, and oxidizing agents such as, peroxides, chlorates, perchlorates, permanganates, and nitrates may cause severe reactions to occur. Nitric acid + ketones and hydrogen can form highly explosive solids or oils.

3. Hazardous decomposition products: None reported.

4. Special precautions: None reported.

* Flammability

The National Fire Protection Association has assigned a flammability rating of 2 (moderate fire hazard) to ethyl butyl ketone.

1. Flash point: 46 degrees C (115 degrees F) (open cup)

2. Autoignition temperature: Data not available.

3. Flammable limits in air (percent by volume): Lower, 1.4; upper, 8.8

4. Extinguishant: For small fires use dry chemical, carbon dioxide, water spray, or alcohol-resistant foam. Use water spray, fog, or alcohol-resistant foam to fight large fires involving ethyl butyl ketone.

Fires involving ethyl butyl ketone should be fought upwind from the maximum distance possible. Keep unnecessary people away; isolate the hazard area and deny entry. Isolate the area for 1/2 mile in all directions if a tank, rail car, or tank truck is involved in the fire. For a massive fire in a cargo area, use unmanned hose holders or monitor nozzles; if this is impossible, withdraw from the area and let the fire burn. Emergency personnel should stay out of low areas. Vapors may travel to a source of ignition and flash back. Vapors are an explosion and poison hazard indoors, outdoors, or in sewers. Containers of ethyl butyl ketone may explode in the heat of the fire and should be moved from the fire area if it is possible to do so safely. If this is not possible, cool fire exposed containers from the sides with water until well after the fire is out. Stay away from the ends of containers. Personnel should withdraw immediately if a rising sound from a venting safety device is heard or if there is discoloration of a container due to fire. Firefighters should wear a full set of protective clothing and self-contained breathing apparatus when fighting fires involving ethyl butyl ketone.

EXPOSURE LIMITS

* OSHA PEL

The current Occupational Safety and Health Administration (OSHA) permissible exposure limit (PEL) for ethyl butyl ketone is 50 parts per million (ppm) parts of air (230 milligrams per cubic meter (mg/m(3))) as an 8-hour time-weighted average (TWA) concentration [29 CFR 1910.1000, Table Z-1].

* NIOSH REL

The National Institute for Occupational Safety and Health (NIOSH) has established a recommended exposure limit (REL) for ethyl butyl ketone of 50 ppm (230 mg/m(3)) as a TWA for up to a 10-hour workday and a 40-hour workweek [NIOSH 1992].

* ACGIH TLV

The American Conference of Governmental Industrial Hygienists (ACGIH) has assigned ethyl butyl ketone a threshold limit value (TLV) of 50 ppm (234 mg/m(3)) as a TWA for a normal 8-hour workday and a 40-hour workweek [ACGIH 1994, p. 21].

* Rationale for Limits

The NIOSH limit is based on the risk of skin and respiratory irritation [NIOSH 1992].

The ACGIH limit is based on the risk of eye irritation and narcosis [ACGIH 1991, p. 592].

HEALTH HAZARD INFORMATION

* Routes of Exposure

Exposure to ethyl butyl ketone can occur through inhalation, ingestion, and eye or skin contact [Sittig 1991].

* Summary of toxicology

1. Effects on Animals: Ethyl butyl ketone is irritating to the skin and eyes of animals and produces narcosis at high concentrations. The acute toxicity of ethyl butyl ketone is low by all routes of exposure. The acute oral LD(50) in rats is 2.76 grams/kg, and the LD(50) for percutaneous absorption in rabbits is greater than 30 ml/kg. Rats exposed to 3,000 ppm for 6 hours is survived, however, exposure to 4,000 ppm for 4 was lethal to all experimental animals [Hathaway et al. 1991; ACGIH 1991]. Rats and guinea pigs exposed for 6 hours daily for 10 days to 400 to 500 ppm of ethyl butyl ketone exhibited vasodilation and eye tearing. At autopsy, no pathology of the lungs, liver, or kidneys was observed. Rats gavaged with 2 g/kg/day for 5 days/week for 14 weeks developed hind limb weakness and tail drag, both signs of neurotoxicity. However, rats exposed to 700 ppm for 72 hours/week for 24 weeks or 60 1 percent ethyl butyl ketone in their drinking water showed no signs of neurotoxicity [Clayton and Clayton 1982; Hathaway et al. 1991]. When ethyl butyl ketone is instilled into the eyes of rabbits or applied directly to the skin, it causes mild irritation [Hathaway et al. 1991].

2. Effects on Humans: Direct contact of ethyl butyl ketone with the skin for 48 hours caused no skin irritation in humans, and sensitization has not been reported [ACGIH 1991]. Ingestion causes irritation of the gastrointestinal tract and the same signs and symptoms of narcosis as inhalation [NLM 1992]. Repeated skin exposure may cause drying and dermatitis [Genium 1994].

* Signs and symptoms of exposure

1. Acute exposure: Mild eye and skin irritation occur on exposure to ethyl butyl ketone. At high concentrations or after ingestion, headache, nausea, vomiting, drowsiness, dizziness, general intoxication, incoordination, and unconsciousness may occur [NLM 1992].

2. Chronic exposure: Repeated exposure of the skin may result in skin drying and dermatitis [Genium 1994].

EMERGENCY MEDICAL PROCEDURES

* Emergency medical procedures: [NIOSH to supply]

5. Rescue: Remove an incapacitated worker from further exposure and implement appropriate emergency procedures (e.g., those listed on the Material Safety Data Sheet required by OSHA's Hazard Communication Standard [29 CFR 1910.1200]). All workers should be familiar with emergency procedures, the location and proper use of emergency equipment, and methods of protecting themselves during rescue operations.

EXPOSURE SOURCES AND CONTROL METHODS

The following operations may involve ethyl butyl ketone and lead to worker exposures to this substance:

* The manufacture and transportation of ethyl butyl ketone

* Liberated during application of lacquers, varnishes, epoxies, vinyl coatings, finishes, and adhesives

* Use as a solvent for nitrocellulose and polyvinyl resins, paints, and lacquers

* Liberated during oven or air drying of coatings and adhesives and during use of cellulosic household cements

* Use as an intermediate in organic synthesis and as a food flavoring

Methods that are effective in controlling worker exposures to ethyl butyl ketone, depending on the feasibility of implementation, are as follows:

* Process enclosure

* Local exhaust ventilation

* General dilution ventilation

* Personal protective equipment

Workers responding to a release or potential release of a hazardous substance must be protected as required by paragraph (q) of OSHA's Hazardous Waste Operations and Emergency Response Standard [29 CFR 1910.120].

Good sources of information about control methods are as follows:

1. ACGIH [1992]. Industrial ventilation--a manual of recommended practice. 21st ed. Cincinnati, OH: American Conference of Governmental Industrial Hygienists.

2. Burton DJ [1986]. Industrial ventilation--a self study companion. Cincinnati, OH: American Conference of Governmental Industrial Hygienists.

3. Alden JL, Kane JM [1982]. Design of industrial ventilation systems. New York, NY: Industrial Press, Inc.

4. Wadden RA, Scheff PA [1987]. Engineering design for control of workplace hazards. New York, NY: McGraw-Hill.

5. Plog BA [1988]. Fundamentals of industrial hygiene. Chicago, IL: National Safety Council.

MEDICAL SURVEILLANCE

OSHA is currently developing requirements for medical surveillance. When these requirements are promulgated, readers should refer to them for additional information and to determine whether employers whose employees are exposed to ethyl butyl ketone are required to implement medical surveillance procedures.

* Medical Screening

Workers who may be exposed to chemical hazards should be monitored in a systematic program of medical surveillance that is intended to prevent occupational injury and disease. The program should include education of employers and workers about work-related hazards, early detection of adverse health effects, and referral of workers for diagnosis and treatment. The occurrence of disease or other work-related adverse health effects should prompt immediate evaluation of primary preventive measures (e.g., industrial hygiene monitoring, engineering controls, and personal protective equipment). A medical surveillance program is intended to supplement, not replace, such measures. To detect and control work-related health effects, medical evaluations should be performed (1) before job placement, (2) periodically during the term of employment, and (3) at the time of job transfer or termination.

* Preplacement medical evaluation

Before a worker is placed in a job with a potential for exposure to ethyl butyl ketone, a licensed health care professional should evaluate and document the worker's baseline health status with thorough medical, environmental, and occupational histories, a physical examination, and physiologic and laboratory tests appropriate for the anticipated occupational risks. These should concentrate on the function and integrity of the eye, skin, and respiratory system. Medical surveillance for respiratory disease should be conducted using the principles and methods recommended by the American Thoracic Society.

A preplacement medical evaluation is recommended to assess medical conditions that may be aggravated or may result in increased risk when a worker is exposed to ethyl butyl ketone at or below the prescribed exposure limit. The health care professional should consider the probable frequency, intensity, and duration of exposure as well as the nature and degree of any applicable medical condition. Such conditions (which should not be regarded as absolute contraindications to job placement) include a history and other findings consistent with diseases of the eye, skin, and respiratory system.

* Periodic medical evaluations

Occupational health interviews and physical examinations should be performed at regular intervals during the employment period, as mandated by any applicable Federal, State, or local standard. Where no standard exists and the hazard is minimal, evaluations should be conducted every 3 to 5 years or as frequently as recommended by an experienced occupational health physician. Additional examinations may be necessary if a worker develops symptoms attributable to ethyl butyl ketone exposure. The interviews, examinations, and medical screening tests should focus on identifying the adverse effects of ethyl butyl ketone on the eye, skin, and respiratory system. Current health status should be compared with the baseline health status of the individual worker or with expected values for a suitable reference population.

* Termination medical evaluations

The medical, environmental, and occupational history interviews, the physical examination, and selected physiologic or laboratory tests that were conducted at the time of placement should be repeated at the time of job transfer or termination to determine the worker's medical status at the end of his or her employment. Any changes in the worker's health status should be compared with those expected for a suitable reference population.

* Biological monitoring

Biological monitoring involves sampling and analyzing body tissues or fluids to provide an index of exposure to a toxic substance or metabolite. No biological monitoring test acceptable for routine use has yet been developed for ethyl butyl ketone.

WORKPLACE MONITORING AND MEASUREMENT

Determination of a worker's exposure to airborne ethyl butyl ketone is made using a charcoal tube (100/50 mg sections, 20/40 mesh. Samples are collected at a maximum flow rate of 0.2 liters/minute until a maximum collection volume of 25 liters is reached. The sample is then treated with 99:1 carbon disulfide:methanol. Analysis is conducted by gas chromatography using a flame ionization detector (GC/FID). This method is fully validated and is described in the OSHA Computerized Information System [OSHA 1994] and in NIOSH Method No. 1301 (ketones) [NIOSH 1994].

PERSONAL HYGIENE PROCEDURES

If ethyl butyl ketone contacts the skin, workers should flush the affected areas immediately with plenty of water, followed by washing with soap and water.

Clothing contaminated with ethyl butyl ketone should be removed immediately, and provisions should be made for the safe removal of the chemical from the clothing. Persons laundering the clothes should be informed of the hazardous properties of ethyl butyl ketone, particularly its potential for causing irritation.

A worker who handles ethyl butyl ketone should thoroughly wash hands, forearms, and face with soap and water before eating, using tobacco products, using toilet facilities, applying cosmetics, or taking medication.

Workers should not eat, drink, use tobacco products, apply cosmetics, or take medication in areas where ethyl butyl ketone or a solution containing ethyl butyl ketone is handled, processed, or stored.

STORAGE

Ethyl butyl ketone should be stored in a cool, dry, well-ventilated area in tightly sealed containers that are labeled in accordance with OSHA's Hazard Communication Standard [29 CFR 1910.1200]. Containers of ethyl butyl ketone should be protected from physical damage and ignition sources, and should be stored separately from acetaldehyde, perchloric acid, and oxidizing agents such as, peroxides, chlorates, perchlorates, permanganates, and nitrates.

SPILLS AND LEAKS

In the event of a spill or leak involving ethyl butyl ketone, persons not wearing protective equipment and clothing should be restricted from contaminated areas until cleanup has been completed. The following steps should be undertaken following a spill or leak:

1. Notify safety personnel.

2. Remove all sources of heat and ignition.

3. Ventilate potentially explosive atmospheres.

4. Do not touch the spilled material; stop the leak if it is possible to do so without risk.

5. Use non-sparking tools.

6. Water spray may be used to reduce vapors. Do not flush material to sewers, watersheds, or waterways.

7. For small liquid spills, take up with sand or other noncombustible absorbent material and place into closed containers for later disposal.

8. For large liquid spills, build dikes far ahead of the spill to contain the ethyl butyl ketone for later reclamation or disposal.

SPECIAL REQUIREMENTS

U.S. Environmental Protection Agency (EPA) requirements for emergency planning, reportable quantities of hazardous releases, community right-to-know, and hazardous waste management may change over time. Users are therefore advised to determine periodically whether new information is available.

* Emergency planning requirements

Ethyl butyl ketone is not subject to EPA emergency planning requirements under the Superfund Amendments and Reauthorization Act (SARA) (Title III) in 42 USC 11022.

* Reportable quantity requirements for hazardous releases

A hazardous substance release is defined by EPA as any spilling, leaking, pumping, pouring, emitting, emptying, discharging, injecting, escaping, leaching, dumping, or disposing into the environment (including the abandonment or discarding of contaminated containers) of hazardous substances. In the event of a release that is above the reportable quantity for that chemical, employers are required to notify the proper Federal, State, and local authorities [40 CFR 355.40].

Employers are not required by the emergency release notification provisions in 40 CFR Part 355.40 to notify the National Response Center of an accidental release of ethyl butyl ketone; there is no reportable quantity for this substance.

* Community right-to-know requirements

Employers are not required by EPA in 40 CFR Part 372.30 to submit a Toxic Chemical Release Inventory form (Form R) to EPA reporting the amount of ethyl butyl ketone emitted or released from their facility annually.

* Hazardous waste management requirements

EPA considers a waste to be hazardous if it exhibits any of the following characteristics: ignitability, corrosivity, reactivity, or toxicity as defined in 40 CFR 261.21-261.24. Under the Resource Conservation and Recovery Act (RCRA) [40 USC 6901 et seq.], EPA has specifically listed many chemical wastes as hazardous. Although ethyl butyl ketone is not specifically listed as a hazardous waste under RCRA, EPA requires employers to treat waste as hazardous if it exhibits any of the characteristics discussed above.

Providing detailed information about the removal and disposal of specific chemicals is beyond the scope of this guideline. The U.S. Department of Transportation, EPA, and State and local regulations should be followed to ensure that removal, transport, and disposal of this substance are conducted in accordance with existing regulations. To be certain that chemical waste disposal meets EPA regulatory requirements, employers should address any questions to the RCRA hotline at (703) 412-9810 (in the Washington, D.C. area) or toll-free at (800) 424-9346 (outside Washington, D.C.). In addition, relevant State and local authorities should be contacted for information on any requirements they may have for the waste removal and disposal of this substance.

RESPIRATORY PROTECTION

* Conditions for respirator use

Good industrial hygiene practice requires that engineering controls be used where feasible to reduce workplace concentrations of hazardous materials to the prescribed exposure limit. However, some situations may require the use of respirators to control exposure. Respirators must be worn if the ambient concentration of ethyl butyl ketone exceeds prescribed exposure limits. Respirators may be used (1) before engineering controls have been installed, (2) during work operations such as maintenance or repair activities that involve unknown exposures, (3) during operations that require entry into tanks or closed vessels, and (4) during emergencies. Workers should only use respirators that have been approved by NIOSH and the Mine Safety and Health Administration (MSHA).

* Respiratory protection program

Employers should institute a complete respiratory protection program that, at a minimum, complies with the requirements of OSHA's Respiratory Protection Standard [29 CFR 1910.134]. Such a program must include respirator selection, an evaluation of the worker's ability to perform the work while wearing a respirator, the regular training of personnel, respirator fit testing, periodic workplace monitoring, and regular respirator maintenance, inspection, and cleaning. The implementation of an adequate respiratory protection program (including selection of the correct respirator) requires that a knowledgeable person be in charge of the program and that the program be evaluated regularly. For additional information on the selection and use of respirators and on the medical screening of respirator users, consult the latest edition of the NIOSH Respirator Decision Logic [NIOSH 1987b] and the NIOSH Guide to Industrial Respiratory Protection [NIOSH 1987a].

PERSONAL PROTECTIVE EQUIPMENT

Workers should use appropriate personal protective clothing and equipment that must be carefully selected, used, and maintained to be effective in preventing skin contact with ethyl butyl ketone. The selection of the appropriate personal protective equipment (PPE) (e.g., gloves, sleeves, encapsulating suits) should be based on the extent of the worker's potential exposure to ethyl butyl ketone. There are no published reports on the resistance of various materials to permeation by ethyl butyl ketone.

To evaluate the use of PPE materials with ethyl butyl ketone, users should consult the best available performance data and manufacturers' recommendations. Significant differences have been demonstrated in the chemical resistance of generically similar PPE materials (e.g., butyl) produced by different manufacturers. In addition, the chemical resistance of a mixture may be significantly different from that of any of its neat components.

Any chemical-resistant clothing that is used should be periodically evaluated to determine its effectiveness in preventing dermal contact. Safety showers and eye wash stations should be located close to operations that involve ethyl butyl ketone.

Splash-proof chemical safety goggles or face shields (20 to 30 cm long, minimum) should be worn during any operation in which a solvent, caustic, or other toxic substance may be splashed into the eyes.

In addition to the possible need for wearing protective outer apparel (e.g., aprons, encapsulating suits), workers should wear work uniforms, coveralls, or similar full-body coverings that are laundered each day. Employers should provide lockers or other closed areas to store work and street clothing separately. Employers should collect work clothing at the end of each work shift and provide for its laundering. Laundry personnel should be informed about the potential hazards of handling contaminated clothing and instructed about measures to minimize their health risk.

Protective clothing should be kept free of oil and grease and should be inspected and maintained regularly to preserve its effectiveness.

Protective clothing may interfere with the body's heat dissipation, especially during hot weather or during work in hot or poorly ventilated work environments.

REFERENCES

ACGIH [1991]. Documentation of the threshold limit values and biological exposure indices. 6th ed. Cincinnati, OH: American Conference of Governmental Industrial Hygienists.

ACGIH [1994]. 1994-1995 Threshold limit values for chemical substances and physical agents and biological exposure indices. Cincinnati, OH: American Conference of Governmental Industrial Hygienists.

ATS [1987]. Standardization of spirometry -- 1987 update. American Thoracic Society. Am Rev Respir Dis 136:1285-1296.

CFR. Code of Federal regulations. Washington, DC: U.S. Government Printing Office, Office of the Federal Register.

Clayton G, Clayton F [1981-1982]. Patty's industrial hygiene and toxicology. 3rd rev. ed. New York, NY: John Wiley & Sons.

DOT [1993]. 1993 Emergency response guidebook, guide 26. Washington, DC: U.S. Department of Transportation, Office of Hazardous Materials Transportation, Research and Special Programs Administration.

Genium [1994]. Material safety data sheet No. 306. Schenectady, NY: Genium Publishing Corporation.

Hathaway GJ, Proctor NH, Hughes JP, and Fischman ML [1991]. Proctor and Hughes' chemical hazards of the workplace. 3rd ed. New York, NY: Van Nostrand Reinhold.

Lewis RJ, ed. [1993]. Lewis condensed chemical dictionary. 12th ed. New York, NY: Van Nostrand Reinhold Company.

Lide DR [1993]. CRC handbook of chemistry and physics. 73rd ed. Boca Raton, FL: CRC Press, Inc.

Mickelsen RL, Hall RC [1987]. A breakthrough time comparison of nitrile and neoprene glove materials produced by different glove manufacturers. Am Ind Hyg Assoc J 48(11): 941-947.

Mickelsen RL, Hall RC, Chern RT, Myers JR [1991]. Evaluation of a simple weight-loss method for determining the permeation of organic liquids through rubber films. Am Ind Hyg Assoc J 52(10): 445-447.

NFPA [1986]. Fire protection guide on hazardous materials. 9th ed. Quincy, MA: National Fire Protection Association.

NIOSH [1987a]. NIOSH guide to industrial respiratory protection. Cincinnati, OH: U.S. Department of Health and Human Services, Public Health Service, Centers for Disease Control, National Institute for Occupational Safety and Health, DHHS (NIOSH) Publication No. 87-116.

NIOSH [1987b]. NIOSH respirator decision logic. Cincinnati, OH: U.S. Department of Health and Human Services, Public Health Service, Centers for Disease Control, National Institute for Occupational Safety and Health, DHHS (NIOSH) Publication No. 87-108.

NIOSH [1991]. Registry of toxic effects of chemical substances: Ethyl Butyl Ketone. Cincinnati, OH: U.S. Department of Health and Human Services, Public Health Service, Centers for Disease Control, National Institute for Occupational Safety and Health, Division of Standards Development and Technology Transfer, Technical Information Branch.

NIOSH [1992]. Recommendations for occupational safety and health: Compendium of policy documents and statements. Cincinnati, OH: U.S. Department of Health and Human Services, Public Health Service, Centers for Disease Control, National Institute for Occupational Safety and Health, DHHS (NIOSH) Publication No. 92-100.

NIOSH [1994]. NIOSH manual of analytical methods. 4th ed. Cincinnati, OH: U.S. Department of Health and Human Services, Public Health Service, Centers for Disease Control, National Institute for Occupational Safety and Health, DHHS (NIOSH) Publication No. 94-113.

NJDH [1986]. Hazardous substance fact sheet: Ethyl Butyl Ketone. Trenton, NJ: New Jersey Department of Health.

NLM [1992]. Hazardous substances data bank: Ethyl Butyl Ketone. Bethesda, MD: National Library of Medicine.

OSHA [1994]. Computerized information system. Washington, DC: U.S. Department of Labor, Occupational Safety and Health Administration.

Patnaik P [1992]. A comprehensive guide to the hazardous properties of chemical substances. New York, NY: Van Nostrand Reinhold.

Sax NI, Lewis RJ [1989]. Dangerous properties of industrial materials. 7th ed. New York, NY: Van Nostrand Reinhold Company.

Sittig M [1991]. Handbook of toxic and hazardous chemicals. 3rd ed. Park Ridge, NJ: Noyes Publications.

USC. United States code. Washington, DC: U.S. Government Printing Office.