Surface preparation may range from a simple wipe down to a total stripping of coating.
Cleaning solvents and degreasers may expose workers to the following:
|
Respiratory Hazards |
Potential Hazards:
Toxic vapors or corrosive mists produced by cleaning agents such as
freons or trichloroethane may present significant health hazards including oxygen-deficient atmospheres. When used in confined or enclosed spaces,
these agents produce vapors that are often heavier than air. This can
cause displacement of air, reducing oxygen levels, which may be fatal.
Requirements and Example Solutions:
- Ensure adequate ventilation to maintain concentrations below the PEL.
[1915.32(a)(2)]
- The Shipyard Competent Person (SCP) may require continual monitoring to
determine air concentrations are within the PELs and below IDLH levels. If they are not, additional engineering controls (e.g., ventilation), administrative controls or PPE (e.g. respirators) must
be used. [1915.32(a)(3)]
- Airline respirators may be necessary if ventilation is not adequate.
- Respirators must comply with 1915.154.
[1910.134]
Additional Resources:
|
Figure 5: Workers protected from toxic cleaning solvents.
Figure 6: Ventilation provided for painting in confined space.
Figure 7: Airline respirator for use when ventilation does not provide adequate safety. |
Back to Top |
|
|
|
Contact Hazards |
Potential Hazards:
Toxic solvents can harm employees eyes and/or skin. Note:
Workers should understand the hazards associated with the materials used
and contained in the space. This
includes training in accordance with the Hazard Communication
Standard. [1915.1200]
Hazards include:
- Organ damage by absorption through the skin or eye.
- Eye or skin irritation.
- Defatting of skin.
Requirements and Example Solutions:
- Appropriate PPE must be used.
- Solvents spills must be cleaned up immediately. [1915.13(b)(5)]
- Washing facilities must be available. [1915.97(b)]
Additional Resources:
|
Figure 8: Worker exposed to health hazards from skin absorption and eye contact.
Figure 9: Worker protected from toxic paint fumes with proper PPE.
Figure 10: Worker protected by PPE from toxic paint fumes and spills while mixing paint.
|
|
|
Maritime
Labor/Industry Recommendations |
- Fixed or portable eye wash stations/safety showers should meet ANSI
Z358.1-1998: Emergency Eye Wash and Shower Equipment.
|
Figure 11: Eye wash station. |
|
Back to Top |
|
|
|
Limited Access |
Potential Hazards:
When working in confined or enclosed spaces workers may become trapped and
unable to exit due to:
- Improperly located equipment.
- Ventilation ducts and hoses running through the opening.
Requirements and Example Solutions:
- When employees work in confined spaces with limited access, the
access must not be blocked or impeded by ventilation ducts, hoses or
other equipment. [1915.76(b)(2)]
- More than one means of access must be provided where practical. [1915.76(b)(1)]
- Additional openings should be considered for ducts, hoses, and other
equipment.
|
Figure 12: Ventilation hoses blocking exit from opening.
Figure 13: Special ventilation hose (flat) to avoid blocking
exit.
Figure 14: Two access holes for equipment or access. |
|
Back to Top
|
|
|
|
Slips and Trips |
Potential Hazards:
Workers performing surface preparation are exposed
to slick conditions and tripping hazards.
- Slipping and falling on oily decks.
- Tripping over equipment, hoses, and vessel structures.
Requirements and Example Solutions:
|
Figure 15: Wet and oily surfaces create slipping hazard.
Figure 16: Tripping hazards due to poor housekeeping.
Figure 17: Lead racks used to remove tripping hazards (welding leads, hoses, etc.) from the deck.
|
|
Back to Top
|
|
|
|
Fall Hazards |
Potential Hazards:
Fall hazards are a leading cause of shipyard fatalities.
Shipyard employees are often required to work in dangerous
environments that may include fall hazards. Accidents involving
elevation equipment such as ladders and scaffolds are often serious,
even fatal.
- Falls from ladders.
- Falls from scaffolds.
- Falls from open deck edges.
- Falls into open holes.
Requirements and Example Solutions:
Guarding of Deck Openings and Edges
- Openings and deck edges must be guarded. [1915.73]
- Flush manholes and other small openings must be guarded after opening. [1915.73(b)]
- During the installation of guards on large openings and deck
edges, fall protection (e.g., harness with lanyard) must be used. [1915.73(d)]
- When floor plates or gratings (e.g. bilges, engine rooms,
pump rooms, machinery spaces) are removed, the
openings must be guarded or planked. [1915.73(f)]
Fall Protection for Scaffold Work
- Guardrails or other appropriate fall protection must be
used when working on scaffolds five feet above surfaces. [1915.71(j)]
- Fall protection must be used during the installation of guards on
scaffolds. [1915.73(d)]
|
Figure 18: Improper use of step ladder.
Figure 19: Several unguarded deck openings.
Figure 20: Properly guarded deck edges.
Figure 21: Worker on scaffold protected by guardrails.
|
|
|
Maritime
Labor/Industry Recommendations |
- SHAC recommends that personal fall protection including
lanyards and harnesses be used and secured during installation
of guardrails.
|
|
Back to Top |
|
|
|
Work Environment Temperature Related Hazards |
Potential Hazards:
Environmental hazards include temperature, humidity, and air movement within the work area. A combination of PPE
use, heat producing equipment, work activity, and environmental conditions
can cause temperature related illnesses.
Heat related illnesses include:
- Heat Stress
- Heat Stroke
- Heat Cramps
- Dehydration
Cold related illnesses include:
Additional Resources:
|
Figure 22: Full body suit can increase potential heat related illnesses for worker.
Figure 23: Air supplied to hood also reduces heat related problems.
|
|
|
Maritime
Labor/Industry Recommendations |
Example Solutions:
SHAC recommends the following for heat related illnesses:
- Plenty of fluids
- Frequent breaks
- Ice vest
- Shaded or cooled break areas
- Ventilation
- Awareness training
SHAC recommends the following for cold related illnesses:
- Appropriate insulated PPE
- Warming areas for breaks
- Awareness training
|
Figure 24: Workers can be trained to recognize and avoid temperature related hazards. |
|
Back to Top
|
|
|
|
Electrical
Hazards |
Potential Hazards:
Employees who work with electrical equipment in wet or damp
locations have an increased risk getting shocked or electrocuted due to:
- Faulty electrical connection in power tools.
- Open lighting parts.
- Broken insulation on power cords.
Requirements and Example Solutions:
- Portable electrical tools must be grounded or double
insulated. [1915.132(a)]
- Temporary lighting must be grounded. [1915.92(c)]
- Power and lighting cables must be inspected by a person
competent to evaluate electrical hazards. (Note: This
is not the Shipyard Competent Person).
[1915.36(a)(5)]
|
Figure 25: Worker inspecting broken insulation on
power cable.
Figure 26: Portable electrical tools must be double insulated or properly grounded.
|
|
|
Maritime
Labor/Industry Recommendations |
- All electrical tools or equipment should undergo a visual
inspection prior to use.
- All portable electric hand tools and temporary lighting
systems should utilize Ground Fault Interrupters (GFI).
- Electrical tools and equipment should correspond with the
requirements of the job.
- Electrical equipment and tools should be used with proper
circuit protection for the voltage and amperage used.
- Only qualified electricians should attempt repair of
electrical tools and equipment in use.
- A Ground Assurance Program should be in place for all
electrical tools and equipment used including:
- Records of tools inspected and repaired.
- Records of electrical boxes inspected and repaired.
- Records of electrical extension cords inspected and
repaired.
- Recall of records of the above.
- The requirements of the Ground Assurance Program should be performed on a
regular basis.
|
Figure 27: Visual inspection takes defective welding
tong out of service. |
|
Back to Top
|
|
|
|
www.osha.gov
